| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iommu: Clear iommu-dma ops on cleanup
If iommu_device_register() encounters an error, it can end up tearing
down already-configured groups and default domains, however this
currently still leaves devices hooked up to iommu-dma (and even
historically the behaviour in this area was at best inconsistent across
architectures/drivers...) Although in the case that an IOMMU is present
whose driver has failed to probe, users cannot necessarily expect DMA to
work anyway, it's still arguable that we should do our best to put
things back as if the IOMMU driver was never there at all, and certainly
the potential for crashing in iommu-dma itself is undesirable. Make sure
we clean up the dev->dma_iommu flag along with everything else. |
| In the Linux kernel, the following vulnerability has been resolved:
igc: fix PTM cycle trigger logic
Writing to clear the PTM status 'valid' bit while the PTM cycle is
triggered results in unreliable PTM operation. To fix this, clear the
PTM 'trigger' and status after each PTM transaction.
The issue can be reproduced with the following:
$ sudo phc2sys -R 1000 -O 0 -i tsn0 -m
Note: 1000 Hz (-R 1000) is unrealistically large, but provides a way to
quickly reproduce the issue.
PHC2SYS exits with:
"ioctl PTP_OFFSET_PRECISE: Connection timed out" when the PTM transaction
fails
This patch also fixes a hang in igc_probe() when loading the igc
driver in the kdump kernel on systems supporting PTM.
The igc driver running in the base kernel enables PTM trigger in
igc_probe(). Therefore the driver is always in PTM trigger mode,
except in brief periods when manually triggering a PTM cycle.
When a crash occurs, the NIC is reset while PTM trigger is enabled.
Due to a hardware problem, the NIC is subsequently in a bad busmaster
state and doesn't handle register reads/writes. When running
igc_probe() in the kdump kernel, the first register access to a NIC
register hangs driver probing and ultimately breaks kdump.
With this patch, igc has PTM trigger disabled most of the time,
and the trigger is only enabled for very brief (10 - 100 us) periods
when manually triggering a PTM cycle. Chances that a crash occurs
during a PTM trigger are not 0, but extremely reduced. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/core: Silence oversized kvmalloc() warning
syzkaller triggered an oversized kvmalloc() warning.
Silence it by adding __GFP_NOWARN.
syzkaller log:
WARNING: CPU: 7 PID: 518 at mm/util.c:665 __kvmalloc_node_noprof+0x175/0x180
CPU: 7 UID: 0 PID: 518 Comm: c_repro Not tainted 6.11.0-rc6+ #6
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:__kvmalloc_node_noprof+0x175/0x180
RSP: 0018:ffffc90001e67c10 EFLAGS: 00010246
RAX: 0000000000000100 RBX: 0000000000000400 RCX: ffffffff8149d46b
RDX: 0000000000000000 RSI: ffff8881030fae80 RDI: 0000000000000002
RBP: 000000712c800000 R08: 0000000000000100 R09: 0000000000000000
R10: ffffc90001e67c10 R11: 0030ae0601000000 R12: 0000000000000000
R13: 0000000000000000 R14: 00000000ffffffff R15: 0000000000000000
FS: 00007fde79159740(0000) GS:ffff88813bdc0000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000020000180 CR3: 0000000105eb4005 CR4: 00000000003706b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
ib_umem_odp_get+0x1f6/0x390
mlx5_ib_reg_user_mr+0x1e8/0x450
ib_uverbs_reg_mr+0x28b/0x440
ib_uverbs_write+0x7d3/0xa30
vfs_write+0x1ac/0x6c0
ksys_write+0x134/0x170
? __sanitizer_cov_trace_pc+0x1c/0x50
do_syscall_64+0x50/0x110
entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
HID: pidff: Fix null pointer dereference in pidff_find_fields
This function triggered a null pointer dereference if used to search for
a report that isn't implemented on the device. This happened both for
optional and required reports alike.
The same logic was applied to pidff_find_special_field and although
pidff_init_fields should return an error earlier if one of the required
reports is missing, future modifications could change this logic and
resurface this possible null pointer dereference again.
LKML bug report:
https://lore.kernel.org/all/CAL-gK7f5=R0nrrQdPtaZZr1fd-cdAMbDMuZ_NLA8vM0SX+nGSw@mail.gmail.com |
| In the Linux kernel, the following vulnerability has been resolved:
page_pool: avoid infinite loop to schedule delayed worker
We noticed the kworker in page_pool_release_retry() was waken
up repeatedly and infinitely in production because of the
buggy driver causing the inflight less than 0 and warning
us in page_pool_inflight()[1].
Since the inflight value goes negative, it means we should
not expect the whole page_pool to get back to work normally.
This patch mitigates the adverse effect by not rescheduling
the kworker when detecting the inflight negative in
page_pool_release_retry().
[1]
[Mon Feb 10 20:36:11 2025] ------------[ cut here ]------------
[Mon Feb 10 20:36:11 2025] Negative(-51446) inflight packet-pages
...
[Mon Feb 10 20:36:11 2025] Call Trace:
[Mon Feb 10 20:36:11 2025] page_pool_release_retry+0x23/0x70
[Mon Feb 10 20:36:11 2025] process_one_work+0x1b1/0x370
[Mon Feb 10 20:36:11 2025] worker_thread+0x37/0x3a0
[Mon Feb 10 20:36:11 2025] kthread+0x11a/0x140
[Mon Feb 10 20:36:11 2025] ? process_one_work+0x370/0x370
[Mon Feb 10 20:36:11 2025] ? __kthread_cancel_work+0x40/0x40
[Mon Feb 10 20:36:11 2025] ret_from_fork+0x35/0x40
[Mon Feb 10 20:36:11 2025] ---[ end trace ebffe800f33e7e34 ]---
Note: before this patch, the above calltrace would flood the
dmesg due to repeated reschedule of release_dw kworker. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: st: Fix array overflow in st_setup()
Change the array size to follow parms size instead of a fixed value. |
| In the Linux kernel, the following vulnerability has been resolved:
accel/ivpu: Fix PM related deadlocks in MS IOCTLs
Prevent runtime resume/suspend while MS IOCTLs are in progress.
Failed suspend will call ivpu_ms_cleanup() that would try to acquire
file_priv->ms_lock, which is already held by the IOCTLs. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: mops: Do not dereference src reg for a set operation
The source register is not used for SET* and reading it can result in
a UBSAN out-of-bounds array access error, specifically when the MOPS
exception is taken from a SET* sequence with XZR (reg 31) as the
source. Architecturally this is the only case where a src/dst/size
field in the ESR can be reported as 31.
Prior to 2de451a329cf662b the code in do_el0_mops() was benign as the
use of pt_regs_read_reg() prevented the out-of-bounds access. |
| In the Linux kernel, the following vulnerability has been resolved:
cifs: avoid NULL pointer dereference in dbg call
cifs_server_dbg() implies server to be non-NULL so
move call under condition to avoid NULL pointer dereference.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: pciehp: Avoid unnecessary device replacement check
Hot-removal of nested PCI hotplug ports suffers from a long-standing race
condition which can lead to a deadlock: A parent hotplug port acquires
pci_lock_rescan_remove(), then waits for pciehp to unbind from a child
hotplug port. Meanwhile that child hotplug port tries to acquire
pci_lock_rescan_remove() as well in order to remove its own children.
The deadlock only occurs if the parent acquires pci_lock_rescan_remove()
first, not if the child happens to acquire it first.
Several workarounds to avoid the issue have been proposed and discarded
over the years, e.g.:
https://lore.kernel.org/r/4c882e25194ba8282b78fe963fec8faae7cf23eb.1529173804.git.lukas@wunner.de/
A proper fix is being worked on, but needs more time as it is nontrivial
and necessarily intrusive.
Recent commit 9d573d19547b ("PCI: pciehp: Detect device replacement during
system sleep") provokes more frequent occurrence of the deadlock when
removing more than one Thunderbolt device during system sleep. The commit
sought to detect device replacement, but also triggered on device removal.
Differentiating reliably between replacement and removal is impossible
because pci_get_dsn() returns 0 both if the device was removed, as well as
if it was replaced with one lacking a Device Serial Number.
Avoid the more frequent occurrence of the deadlock by checking whether the
hotplug port itself was hot-removed. If so, there's no sense in checking
whether its child device was replaced.
This works because the ->resume_noirq() callback is invoked in top-down
order for the entire hierarchy: A parent hotplug port detecting device
replacement (or removal) marks all children as removed using
pci_dev_set_disconnected() and a child hotplug port can then reliably
detect being removed. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: fsl-qspi: use devm function instead of driver remove
Driver use devm APIs to manage clk/irq/resources and register the spi
controller, but the legacy remove function will be called first during
device detach and trigger kernel panic. Drop the remove function and use
devm_add_action_or_reset() for driver cleanup to ensure the release
sequence.
Trigger kernel panic on i.MX8MQ by
echo 30bb0000.spi >/sys/bus/platform/drivers/fsl-quadspi/unbind |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: remove wrong sb->s_sequence check
Journal emptiness is not determined by sb->s_sequence == 0 but rather by
sb->s_start == 0 (which is set a few lines above). Furthermore 0 is a
valid transaction ID so the check can spuriously trigger. Remove the
invalid WARN_ON. |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/tegra241-cmdqv: Fix warnings due to dmam_free_coherent()
Two WARNINGs are observed when SMMU driver rolls back upon failure:
arm-smmu-v3.9.auto: Failed to register iommu
arm-smmu-v3.9.auto: probe with driver arm-smmu-v3 failed with error -22
------------[ cut here ]------------
WARNING: CPU: 5 PID: 1 at kernel/dma/mapping.c:74 dmam_free_coherent+0xc0/0xd8
Call trace:
dmam_free_coherent+0xc0/0xd8 (P)
tegra241_vintf_free_lvcmdq+0x74/0x188
tegra241_cmdqv_remove_vintf+0x60/0x148
tegra241_cmdqv_remove+0x48/0xc8
arm_smmu_impl_remove+0x28/0x60
devm_action_release+0x1c/0x40
------------[ cut here ]------------
128 pages are still in use!
WARNING: CPU: 16 PID: 1 at mm/page_alloc.c:6902 free_contig_range+0x18c/0x1c8
Call trace:
free_contig_range+0x18c/0x1c8 (P)
cma_release+0x154/0x2f0
dma_free_contiguous+0x38/0xa0
dma_direct_free+0x10c/0x248
dma_free_attrs+0x100/0x290
dmam_free_coherent+0x78/0xd8
tegra241_vintf_free_lvcmdq+0x74/0x160
tegra241_cmdqv_remove+0x98/0x198
arm_smmu_impl_remove+0x28/0x60
devm_action_release+0x1c/0x40
This is because the LVCMDQ queue memory are managed by devres, while that
dmam_free_coherent() is called in the context of devm_action_release().
Jason pointed out that "arm_smmu_impl_probe() has mis-ordered the devres
callbacks if ops->device_remove() is going to be manually freeing things
that probe allocated":
https://lore.kernel.org/linux-iommu/20250407174408.GB1722458@nvidia.com/
In fact, tegra241_cmdqv_init_structures() only allocates memory resources
which means any failure that it generates would be similar to -ENOMEM, so
there is no point in having that "falling back to standard SMMU" routine,
as the standard SMMU would likely fail to allocate memory too.
Remove the unwind part in tegra241_cmdqv_init_structures(), and return a
proper error code to ask SMMU driver to call tegra241_cmdqv_remove() via
impl_ops->device_remove(). Then, drop tegra241_vintf_free_lvcmdq() since
devres will take care of that. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: Fix reference leak in pci_register_host_bridge()
If device_register() fails, call put_device() to give up the reference to
avoid a memory leak, per the comment at device_register().
Found by code review.
[bhelgaas: squash Dan Carpenter's double free fix from
https://lore.kernel.org/r/db806a6c-a91b-4e5a-a84b-6b7e01bdac85@stanley.mountain] |
| In the Linux kernel, the following vulnerability has been resolved:
mm/vmscan: don't try to reclaim hwpoison folio
Syzkaller reports a bug as follows:
Injecting memory failure for pfn 0x18b00e at process virtual address 0x20ffd000
Memory failure: 0x18b00e: dirty swapcache page still referenced by 2 users
Memory failure: 0x18b00e: recovery action for dirty swapcache page: Failed
page: refcount:2 mapcount:0 mapping:0000000000000000 index:0x20ffd pfn:0x18b00e
memcg:ffff0000dd6d9000
anon flags: 0x5ffffe00482011(locked|dirty|arch_1|swapbacked|hwpoison|node=0|zone=2|lastcpupid=0xfffff)
raw: 005ffffe00482011 dead000000000100 dead000000000122 ffff0000e232a7c9
raw: 0000000000020ffd 0000000000000000 00000002ffffffff ffff0000dd6d9000
page dumped because: VM_BUG_ON_FOLIO(!folio_test_uptodate(folio))
------------[ cut here ]------------
kernel BUG at mm/swap_state.c:184!
Internal error: Oops - BUG: 00000000f2000800 [#1] SMP
Modules linked in:
CPU: 0 PID: 60 Comm: kswapd0 Not tainted 6.6.0-gcb097e7de84e #3
Hardware name: linux,dummy-virt (DT)
pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : add_to_swap+0xbc/0x158
lr : add_to_swap+0xbc/0x158
sp : ffff800087f37340
x29: ffff800087f37340 x28: fffffc00052c0380 x27: ffff800087f37780
x26: ffff800087f37490 x25: ffff800087f37c78 x24: ffff800087f377a0
x23: ffff800087f37c50 x22: 0000000000000000 x21: fffffc00052c03b4
x20: 0000000000000000 x19: fffffc00052c0380 x18: 0000000000000000
x17: 296f696c6f662865 x16: 7461646f7470755f x15: 747365745f6f696c
x14: 6f6621284f494c4f x13: 0000000000000001 x12: ffff600036d8b97b
x11: 1fffe00036d8b97a x10: ffff600036d8b97a x9 : dfff800000000000
x8 : 00009fffc9274686 x7 : ffff0001b6c5cbd3 x6 : 0000000000000001
x5 : ffff0000c25896c0 x4 : 0000000000000000 x3 : 0000000000000000
x2 : 0000000000000000 x1 : ffff0000c25896c0 x0 : 0000000000000000
Call trace:
add_to_swap+0xbc/0x158
shrink_folio_list+0x12ac/0x2648
shrink_inactive_list+0x318/0x948
shrink_lruvec+0x450/0x720
shrink_node_memcgs+0x280/0x4a8
shrink_node+0x128/0x978
balance_pgdat+0x4f0/0xb20
kswapd+0x228/0x438
kthread+0x214/0x230
ret_from_fork+0x10/0x20
I can reproduce this issue with the following steps:
1) When a dirty swapcache page is isolated by reclaim process and the
page isn't locked, inject memory failure for the page.
me_swapcache_dirty() clears uptodate flag and tries to delete from lru,
but fails. Reclaim process will put the hwpoisoned page back to lru.
2) The process that maps the hwpoisoned page exits, the page is deleted
the page will never be freed and will be in the lru forever.
3) If we trigger a reclaim again and tries to reclaim the page,
add_to_swap() will trigger VM_BUG_ON_FOLIO due to the uptodate flag is
cleared.
To fix it, skip the hwpoisoned page in shrink_folio_list(). Besides, the
hwpoison folio may not be unmapped by hwpoison_user_mappings() yet, unmap
it in shrink_folio_list(), otherwise the folio will fail to be unmaped by
hwpoison_user_mappings() since the folio isn't in lru list. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: scmi: Fix null-ptr-deref in scmi_cpufreq_get_rate()
cpufreq_cpu_get_raw() can return NULL when the target CPU is not present
in the policy->cpus mask. scmi_cpufreq_get_rate() does not check for
this case, which results in a NULL pointer dereference.
Add NULL check after cpufreq_cpu_get_raw() to prevent this issue. |
| In the Linux kernel, the following vulnerability has been resolved:
cpufreq: scpi: Fix null-ptr-deref in scpi_cpufreq_get_rate()
cpufreq_cpu_get_raw() can return NULL when the target CPU is not present
in the policy->cpus mask. scpi_cpufreq_get_rate() does not check for
this case, which results in a NULL pointer dereference. |
| A flaw was found in virtio-win, specifically within the VirtIO Block (BLK) device. When the device undergoes a reset, it fails to properly manage memory, resulting in a use-after-free vulnerability. This issue could allow a local attacker to corrupt system memory, potentially leading to system instability or unexpected behavior. |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix NULL pointer dereference in tipc_mon_reinit_self()
syzbot reported:
tipc: Node number set to 1055423674
Oops: general protection fault, probably for non-canonical address 0xdffffc0000000000: 0000 [#1] SMP KASAN NOPTI
KASAN: null-ptr-deref in range [0x0000000000000000-0x0000000000000007]
CPU: 3 UID: 0 PID: 6017 Comm: kworker/3:5 Not tainted 6.15.0-rc1-syzkaller-00246-g900241a5cc15 #0 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2~bpo12+1 04/01/2014
Workqueue: events tipc_net_finalize_work
RIP: 0010:tipc_mon_reinit_self+0x11c/0x210 net/tipc/monitor.c:719
...
RSP: 0018:ffffc9000356fb68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003ee87cba
RDX: 0000000000000000 RSI: ffffffff8dbc56a7 RDI: ffff88804c2cc010
RBP: dffffc0000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007
R13: fffffbfff2111097 R14: ffff88804ead8000 R15: ffff88804ead9010
FS: 0000000000000000(0000) GS:ffff888097ab9000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f720eb00 CR3: 000000000e182000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
tipc_net_finalize+0x10b/0x180 net/tipc/net.c:140
process_one_work+0x9cc/0x1b70 kernel/workqueue.c:3238
process_scheduled_works kernel/workqueue.c:3319 [inline]
worker_thread+0x6c8/0xf10 kernel/workqueue.c:3400
kthread+0x3c2/0x780 kernel/kthread.c:464
ret_from_fork+0x45/0x80 arch/x86/kernel/process.c:153
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
...
RIP: 0010:tipc_mon_reinit_self+0x11c/0x210 net/tipc/monitor.c:719
...
RSP: 0018:ffffc9000356fb68 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000003ee87cba
RDX: 0000000000000000 RSI: ffffffff8dbc56a7 RDI: ffff88804c2cc010
RBP: dffffc0000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000007
R13: fffffbfff2111097 R14: ffff88804ead8000 R15: ffff88804ead9010
FS: 0000000000000000(0000) GS:ffff888097ab9000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000f720eb00 CR3: 000000000e182000 CR4: 0000000000352ef0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
There is a racing condition between workqueue created when enabling
bearer and another thread created when disabling bearer right after
that as follow:
enabling_bearer | disabling_bearer
--------------- | ----------------
tipc_disc_timeout() |
{ | bearer_disable()
... | {
schedule_work(&tn->work); | tipc_mon_delete()
... | {
} | ...
| write_lock_bh(&mon->lock);
| mon->self = NULL;
| write_unlock_bh(&mon->lock);
| ...
| }
tipc_net_finalize_work() | }
{ |
... |
tipc_net_finalize() |
{ |
... |
tipc_mon_reinit_self() |
{ |
... |
write_lock_bh(&mon->lock); |
mon->self->addr = tipc_own_addr(net); |
write_unlock_bh(&mon->lock); |
...
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
usb: chipidea: ci_hdrc_imx: fix usbmisc handling
usbmisc is an optional device property so it is totally valid for the
corresponding data->usbmisc_data to have a NULL value.
Check that before dereferencing the pointer.
Found by Linux Verification Center (linuxtesting.org) with Svace static
analysis tool. |
