| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_event: move wake reason storage into validated event handlers
hci_store_wake_reason() is called from hci_event_packet() immediately
after stripping the HCI event header but before hci_event_func()
enforces the per-event minimum payload length from hci_ev_table.
This means a short HCI event frame can reach bacpy() before any bounds
check runs.
Rather than duplicating skb parsing and per-event length checks inside
hci_store_wake_reason(), move wake-address storage into the individual
event handlers after their existing event-length validation has
succeeded. Convert hci_store_wake_reason() into a small helper that only
stores an already-validated bdaddr while the caller holds hci_dev_lock().
Use the same helper after hci_event_func() with a NULL address to
preserve the existing unexpected-wake fallback semantics when no
validated event handler records a wake address.
Annotate the helper with __must_hold(&hdev->lock) and add
lockdep_assert_held(&hdev->lock) so future call paths keep the lock
contract explicit.
Call the helper from hci_conn_request_evt(), hci_conn_complete_evt(),
hci_sync_conn_complete_evt(), le_conn_complete_evt(),
hci_le_adv_report_evt(), hci_le_ext_adv_report_evt(),
hci_le_direct_adv_report_evt(), hci_le_pa_sync_established_evt(), and
hci_le_past_received_evt(). |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate response sizes in ipc_validate_msg()
ipc_validate_msg() computes the expected message size for each
response type by adding (or multiplying) attacker-controlled fields
from the daemon response to a fixed struct size in unsigned int
arithmetic. Three cases can overflow:
KSMBD_EVENT_RPC_REQUEST:
msg_sz = sizeof(struct ksmbd_rpc_command) + resp->payload_sz;
KSMBD_EVENT_SHARE_CONFIG_REQUEST:
msg_sz = sizeof(struct ksmbd_share_config_response) +
resp->payload_sz;
KSMBD_EVENT_LOGIN_REQUEST_EXT:
msg_sz = sizeof(struct ksmbd_login_response_ext) +
resp->ngroups * sizeof(gid_t);
resp->payload_sz is __u32 and resp->ngroups is __s32. Each addition
can wrap in unsigned int; the multiplication by sizeof(gid_t) mixes
signed and size_t, so a negative ngroups is converted to SIZE_MAX
before the multiply. A wrapped value of msg_sz that happens to
equal entry->msg_sz bypasses the size check on the next line, and
downstream consumers (smb2pdu.c:6742 memcpy using rpc_resp->payload_sz,
kmemdup in ksmbd_alloc_user using resp_ext->ngroups) then trust the
unverified length.
Use check_add_overflow() on the RPC_REQUEST and SHARE_CONFIG_REQUEST
paths to detect integer overflow without constraining functional
payload size; userspace ksmbd-tools grows NDR responses in 4096-byte
chunks for calls like NetShareEnumAll, so a hard transport cap is
unworkable on the response side. For LOGIN_REQUEST_EXT, reject
resp->ngroups outside the signed [0, NGROUPS_MAX] range up front and
report the error from ipc_validate_msg() so it fires at the IPC
boundary; with that bound the subsequent multiplication and addition
stay well below UINT_MAX. The now-redundant ngroups check and
pr_err in ksmbd_alloc_user() are removed.
This is the response-side analogue of aab98e2dbd64 ("ksmbd: fix
integer overflows on 32 bit systems"), which hardened the request
side. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: validate num_aces and harden ACE walk in smb_inherit_dacl()
smb_inherit_dacl() trusts the on-disk num_aces value from the parent
directory's DACL xattr and uses it to size a heap allocation:
aces_base = kmalloc(sizeof(struct smb_ace) * num_aces * 2, ...);
num_aces is a u16 read from le16_to_cpu(parent_pdacl->num_aces)
without checking that it is consistent with the declared pdacl_size.
An authenticated client whose parent directory's security.NTACL is
tampered (e.g. via offline xattr corruption or a concurrent path that
bypasses parse_dacl()) can present num_aces = 65535 with minimal
actual ACE data. This causes a ~8 MB allocation (not kzalloc, so
uninitialized) that the subsequent loop only partially populates, and
may also overflow the three-way size_t multiply on 32-bit kernels.
Additionally, the ACE walk loop uses the weaker
offsetof(struct smb_ace, access_req) minimum size check rather than
the minimum valid on-wire ACE size, and does not reject ACEs whose
declared size is below the minimum.
Reproduced on UML + KASAN + LOCKDEP against the real ksmbd code path.
A legitimate mount.cifs client creates a parent directory over SMB
(ksmbd writes a valid security.NTACL xattr), then the NTACL blob on
the backing filesystem is rewritten to set num_aces = 0xFFFF while
keeping the posix_acl_hash bytes intact so ksmbd_vfs_get_sd_xattr()'s
hash check still passes. A subsequent SMB2 CREATE of a child under
that parent drives smb2_open() into smb_inherit_dacl() (share has
"vfs objects = acl_xattr" set), which fails the page allocator:
WARNING: mm/page_alloc.c:5226 at __alloc_frozen_pages_noprof+0x46c/0x9c0
Workqueue: ksmbd-io handle_ksmbd_work
__alloc_frozen_pages_noprof+0x46c/0x9c0
___kmalloc_large_node+0x68/0x130
__kmalloc_large_node_noprof+0x24/0x70
__kmalloc_noprof+0x4c9/0x690
smb_inherit_dacl+0x394/0x2430
smb2_open+0x595d/0xabe0
handle_ksmbd_work+0x3d3/0x1140
With the patch applied the added guard rejects the tampered value
with -EINVAL before any large allocation runs, smb2_open() falls back
to smb2_create_sd_buffer(), and the child is created with a default
SD. No warning, no splat.
Fix by:
1. Validating num_aces against pdacl_size using the same formula
applied in parse_dacl().
2. Replacing the raw kmalloc(sizeof * num_aces * 2) with
kmalloc_array(num_aces * 2, sizeof(...)) for overflow-safe
allocation.
3. Tightening the per-ACE loop guard to require the minimum valid
ACE size (offsetof(smb_ace, sid) + CIFS_SID_BASE_SIZE) and
rejecting under-sized ACEs, matching the hardening in
smb_check_perm_dacl() and parse_dacl().
v1 -> v2:
- Replace the synthetic test-module splat in the changelog with a
real-path UML + KASAN reproduction driven through mount.cifs and
SMB2 CREATE; Namjae flagged the kcifs3_test_inherit_dacl_old name
in v1 since it does not exist in ksmbd.
- Drop the commit-hash citation from the code comment per Namjae's
review; keep the parse_dacl() pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
openvswitch: defer tunnel netdev_put to RCU release
ovs_netdev_tunnel_destroy() may run after NETDEV_UNREGISTER already
detached the device. Dropping the netdev reference in destroy can race
with concurrent readers that still observe vport->dev.
Do not release vport->dev in ovs_netdev_tunnel_destroy(). Instead, let
vport_netdev_free() drop the reference from the RCU callback, matching
the non-tunnel destroy path and avoiding additional synchronization
under RTNL. |
| In the Linux kernel, the following vulnerability has been resolved:
net/sched: sch_netem: fix out-of-bounds access in packet corruption
In netem_enqueue(), the packet corruption logic uses
get_random_u32_below(skb_headlen(skb)) to select an index for
modifying skb->data. When an AF_PACKET TX_RING sends fully non-linear
packets over an IPIP tunnel, skb_headlen(skb) evaluates to 0.
Passing 0 to get_random_u32_below() takes the variable-ceil slow path
which returns an unconstrained 32-bit random integer. Using this
unconstrained value as an offset into skb->data results in an
out-of-bounds memory access.
Fix this by verifying skb_headlen(skb) is non-zero before attempting
to corrupt the linear data area. Fully non-linear packets will silently
bypass the corruption logic. |
| In the Linux kernel, the following vulnerability has been resolved:
xfrm: hold dev ref until after transport_finish NF_HOOK
After async crypto completes, xfrm_input_resume() calls dev_put()
immediately on re-entry before the skb reaches transport_finish.
The skb->dev pointer is then used inside NF_HOOK and its okfn,
which can race with device teardown.
Remove the dev_put from the async resumption entry and instead
drop the reference after the NF_HOOK call in transport_finish,
using a saved device pointer since NF_HOOK may consume the skb.
This covers NF_DROP, NF_QUEUE and NF_STOLEN paths that skip
the okfn.
For non-transport exits (decaps, gro, drop) and secondary
async return points, release the reference inline when
async is set. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: move async event work off nvmet-wq
For target nvmet_ctrl_free() flushes ctrl->async_event_work.
If nvmet_ctrl_free() runs on nvmet-wq, the flush re-enters workqueue
completion for the same worker:-
A. Async event work queued on nvmet-wq (prior to disconnect):
nvmet_execute_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
nvmet_add_async_event()
queue_work(nvmet_wq, &ctrl->async_event_work)
B. Full pre-work chain (RDMA CM path):
nvmet_rdma_cm_handler()
nvmet_rdma_queue_disconnect()
__nvmet_rdma_queue_disconnect()
queue_work(nvmet_wq, &queue->release_work)
process_one_work()
lock((wq_completion)nvmet-wq) <--------- 1st
nvmet_rdma_release_queue_work()
C. Recursive path (same worker):
nvmet_rdma_release_queue_work()
nvmet_rdma_free_queue()
nvmet_sq_destroy()
nvmet_ctrl_put()
nvmet_ctrl_free()
flush_work(&ctrl->async_event_work)
__flush_work()
touch_wq_lockdep_map()
lock((wq_completion)nvmet-wq) <--------- 2nd
Lockdep splat:
============================================
WARNING: possible recursive locking detected
6.19.0-rc3nvme+ #14 Tainted: G N
--------------------------------------------
kworker/u192:42/44933 is trying to acquire lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: touch_wq_lockdep_map+0x26/0x90
but task is already holding lock:
ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
3 locks held by kworker/u192:42/44933:
#0: ffff888118a00948 ((wq_completion)nvmet-wq){+.+.}-{0:0}, at: process_one_work+0x53e/0x660
#1: ffffc9000e6cbe28 ((work_completion)(&queue->release_work)){+.+.}-{0:0}, at: process_one_work+0x1c5/0x660
#2: ffffffff82d4db60 (rcu_read_lock){....}-{1:3}, at: __flush_work+0x62/0x530
Workqueue: nvmet-wq nvmet_rdma_release_queue_work [nvmet_rdma]
Call Trace:
__flush_work+0x268/0x530
nvmet_ctrl_free+0x140/0x310 [nvmet]
nvmet_cq_put+0x74/0x90 [nvmet]
nvmet_rdma_free_queue+0x23/0xe0 [nvmet_rdma]
nvmet_rdma_release_queue_work+0x19/0x50 [nvmet_rdma]
process_one_work+0x206/0x660
worker_thread+0x184/0x320
kthread+0x10c/0x240
ret_from_fork+0x319/0x390
Move async event work to a dedicated nvmet-aen-wq to avoid reentrant
flush on nvmet-wq. |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: fix out-of-bounds writes in iavf_get_ethtool_stats()
iavf incorrectly uses real_num_tx_queues for ETH_SS_STATS. Since the
value could change in runtime, we should use num_tx_queues instead.
Moreover iavf_get_ethtool_stats() uses num_active_queues while
iavf_get_sset_count() and iavf_get_stat_strings() use
real_num_tx_queues, which triggers out-of-bounds writes when we do
"ethtool -L" and "ethtool -S" simultaneously [1].
For example when we change channels from 1 to 8, Thread 3 could be
scheduled before Thread 2, and out-of-bounds writes could be triggered
in Thread 3:
Thread 1 (ethtool -L) Thread 2 (work) Thread 3 (ethtool -S)
iavf_set_channels()
...
iavf_alloc_queues()
-> num_active_queues = 8
iavf_schedule_finish_config()
iavf_get_sset_count()
real_num_tx_queues: 1
-> buffer for 1 queue
iavf_get_ethtool_stats()
num_active_queues: 8
-> out-of-bounds!
iavf_finish_config()
-> real_num_tx_queues = 8
Use immutable num_tx_queues in all related functions to avoid the issue.
[1]
BUG: KASAN: vmalloc-out-of-bounds in iavf_add_one_ethtool_stat+0x200/0x270
Write of size 8 at addr ffffc900031c9080 by task ethtool/5800
CPU: 1 UID: 0 PID: 5800 Comm: ethtool Not tainted 6.19.0-enjuk-08403-g8137e3db7f1c #241 PREEMPT(full)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x6f/0xb0
print_report+0x170/0x4f3
kasan_report+0xe1/0x180
iavf_add_one_ethtool_stat+0x200/0x270
iavf_get_ethtool_stats+0x14c/0x2e0
__dev_ethtool+0x3d0c/0x5830
dev_ethtool+0x12d/0x270
dev_ioctl+0x53c/0xe30
sock_do_ioctl+0x1a9/0x270
sock_ioctl+0x3d4/0x5e0
__x64_sys_ioctl+0x137/0x1c0
do_syscall_64+0xf3/0x690
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7f7da0e6e36d
...
</TASK>
The buggy address belongs to a 1-page vmalloc region starting at 0xffffc900031c9000 allocated at __dev_ethtool+0x3cc9/0x5830
The buggy address belongs to the physical page: page: refcount:1 mapcount:0 mapping:0000000000000000
index:0xffff88813a013de0 pfn:0x13a013
flags: 0x200000000000000(node=0|zone=2)
raw: 0200000000000000 0000000000000000 dead000000000122 0000000000000000
raw: ffff88813a013de0 0000000000000000 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffc900031c8f80: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc900031c9000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffffc900031c9080: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
^
ffffc900031c9100: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8
ffffc900031c9180: f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 |
| In the Linux kernel, the following vulnerability has been resolved:
team: fix header_ops type confusion with non-Ethernet ports
Similar to commit 950803f72547 ("bonding: fix type confusion in
bond_setup_by_slave()") team has the same class of header_ops type
confusion.
For non-Ethernet ports, team_setup_by_port() copies port_dev->header_ops
directly. When the team device later calls dev_hard_header() or
dev_parse_header(), these callbacks can run with the team net_device
instead of the real lower device, so netdev_priv(dev) is interpreted as
the wrong private type and can crash.
The syzbot report shows a crash in bond_header_create(), but the root
cause is in team: the topology is gre -> bond -> team, and team calls
the inherited header_ops with its own net_device instead of the lower
device, so bond_header_create() receives a team device and interprets
netdev_priv() as bonding private data, causing a type confusion crash.
Fix this by introducing team header_ops wrappers for create/parse,
selecting a team port under RCU, and calling the lower device callbacks
with port->dev, so each callback always sees the correct net_device
context.
Also pass the selected lower device to the lower parse callback, so
recursion is bounded in stacked non-Ethernet topologies and parse
callbacks always run with the correct device context. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (pmbus/core) Protect regulator operations with mutex
The regulator operations pmbus_regulator_get_voltage(),
pmbus_regulator_set_voltage(), and pmbus_regulator_list_voltage()
access PMBus registers and shared data but were not protected by
the update_lock mutex. This could lead to race conditions.
However, adding mutex protection directly to these functions causes
a deadlock because pmbus_regulator_notify() (which calls
regulator_notifier_call_chain()) is often called with the mutex
already held (e.g., from pmbus_fault_handler()). If a regulator
callback then calls one of the now-protected voltage functions,
it will attempt to acquire the same mutex.
Rework pmbus_regulator_notify() to utilize a worker function to
send notifications outside of the mutex protection. Events are
stored as atomics in a per-page bitmask and processed by the worker.
Initialize the worker and its associated data during regulator
registration, and ensure it is cancelled on device removal using
devm_add_action_or_reset().
While at it, remove the unnecessary include of linux/of.h. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix OOB write in QUERY_INFO for compound requests
When a compound request such as READ + QUERY_INFO(Security) is received,
and the first command (READ) consumes most of the response buffer,
ksmbd could write beyond the allocated buffer while building a security
descriptor.
The root cause was that smb2_get_info_sec() checked buffer space using
ppntsd_size from xattr, while build_sec_desc() often synthesized a
significantly larger descriptor from POSIX ACLs.
This patch introduces smb_acl_sec_desc_scratch_len() to accurately
compute the final descriptor size beforehand, performs proper buffer
checking with smb2_calc_max_out_buf_len(), and uses exact-sized
allocation + iov pinning. |
| In the Linux kernel, the following vulnerability has been resolved:
net: bonding: fix use-after-free in bond_xmit_broadcast()
bond_xmit_broadcast() reuses the original skb for the last slave
(determined by bond_is_last_slave()) and clones it for others.
Concurrent slave enslave/release can mutate the slave list during
RCU-protected iteration, changing which slave is "last" mid-loop.
This causes the original skb to be double-consumed (double-freed).
Replace the racy bond_is_last_slave() check with a simple index
comparison (i + 1 == slaves_count) against the pre-snapshot slave
count taken via READ_ONCE() before the loop. This preserves the
zero-copy optimization for the last slave while making the "last"
determination stable against concurrent list mutations.
The UAF can trigger the following crash:
==================================================================
BUG: KASAN: slab-use-after-free in skb_clone
Read of size 8 at addr ffff888100ef8d40 by task exploit/147
CPU: 1 UID: 0 PID: 147 Comm: exploit Not tainted 7.0.0-rc3+ #4 PREEMPTLAZY
Call Trace:
<TASK>
dump_stack_lvl (lib/dump_stack.c:123)
print_report (mm/kasan/report.c:379 mm/kasan/report.c:482)
kasan_report (mm/kasan/report.c:597)
skb_clone (include/linux/skbuff.h:1724 include/linux/skbuff.h:1792 include/linux/skbuff.h:3396 net/core/skbuff.c:2108)
bond_xmit_broadcast (drivers/net/bonding/bond_main.c:5334)
bond_start_xmit (drivers/net/bonding/bond_main.c:5567 drivers/net/bonding/bond_main.c:5593)
dev_hard_start_xmit (include/linux/netdevice.h:5325 include/linux/netdevice.h:5334 net/core/dev.c:3871 net/core/dev.c:3887)
__dev_queue_xmit (include/linux/netdevice.h:3601 net/core/dev.c:4838)
ip6_finish_output2 (include/net/neighbour.h:540 include/net/neighbour.h:554 net/ipv6/ip6_output.c:136)
ip6_finish_output (net/ipv6/ip6_output.c:208 net/ipv6/ip6_output.c:219)
ip6_output (net/ipv6/ip6_output.c:250)
ip6_send_skb (net/ipv6/ip6_output.c:1985)
udp_v6_send_skb (net/ipv6/udp.c:1442)
udpv6_sendmsg (net/ipv6/udp.c:1733)
__sys_sendto (net/socket.c:730 net/socket.c:742 net/socket.c:2206)
__x64_sys_sendto (net/socket.c:2209)
do_syscall_64 (arch/x86/entry/syscall_64.c:63 arch/x86/entry/syscall_64.c:94)
entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:130)
</TASK>
Allocated by task 147:
Freed by task 147:
The buggy address belongs to the object at ffff888100ef8c80
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 192 bytes inside of
freed 224-byte region [ffff888100ef8c80, ffff888100ef8d60)
Memory state around the buggy address:
ffff888100ef8c00: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
ffff888100ef8c80: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
>ffff888100ef8d00: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
ffff888100ef8d80: fc fc fc fc fc fc fc fc fa fb fb fb fb fb fb fb
ffff888100ef8e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
================================================================== |
| In the Linux kernel, the following vulnerability has been resolved:
net/rds: Fix circular locking dependency in rds_tcp_tune
syzbot reported a circular locking dependency in rds_tcp_tune() where
sk_net_refcnt_upgrade() is called while holding the socket lock:
======================================================
WARNING: possible circular locking dependency detected
======================================================
kworker/u10:8/15040 is trying to acquire lock:
ffffffff8e9aaf80 (fs_reclaim){+.+.}-{0:0},
at: __kmalloc_cache_noprof+0x4b/0x6f0
but task is already holding lock:
ffff88805a3c1ce0 (k-sk_lock-AF_INET6){+.+.}-{0:0},
at: rds_tcp_tune+0xd7/0x930
The issue occurs because sk_net_refcnt_upgrade() performs memory
allocation (via get_net_track() -> ref_tracker_alloc()) while the
socket lock is held, creating a circular dependency with fs_reclaim.
Fix this by moving sk_net_refcnt_upgrade() outside the socket lock
critical section. This is safe because the fields modified by the
sk_net_refcnt_upgrade() call (sk_net_refcnt, ns_tracker) are not
accessed by any concurrent code path at this point.
v2:
- Corrected fixes tag
- check patch line wrap nits
- ai commentary nits |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: release flowtable after rcu grace period on error
Call synchronize_rcu() after unregistering the hooks from error path,
since a hook that already refers to this flowtable can be already
registered, exposing this flowtable to packet path and nfnetlink_hook
control plane.
This error path is rare, it should only happen by reaching the maximum
number hooks or by failing to set up to hardware offload, just call
synchronize_rcu().
There is a check for already used device hooks by different flowtable
that could result in EEXIST at this late stage. The hook parser can be
updated to perform this check earlier to this error path really becomes
rarely exercised.
Uncovered by KASAN reported as use-after-free from nfnetlink_hook path
when dumping hooks. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, arm64: Force 8-byte alignment for JIT buffer to prevent atomic tearing
struct bpf_plt contains a u64 target field. Currently, the BPF JIT
allocator requests an alignment of 4 bytes (sizeof(u32)) for the JIT
buffer.
Because the base address of the JIT buffer can be 4-byte aligned (e.g.,
ending in 0x4 or 0xc), the relative padding logic in build_plt() fails
to ensure that target lands on an 8-byte boundary.
This leads to two issues:
1. UBSAN reports misaligned-access warnings when dereferencing the
structure.
2. More critically, target is updated concurrently via WRITE_ONCE() in
bpf_arch_text_poke() while the JIT'd code executes ldr. On arm64,
64-bit loads/stores are only guaranteed to be single-copy atomic if
they are 64-bit aligned. A misaligned target risks a torn read,
causing the JIT to jump to a corrupted address.
Fix this by increasing the allocation alignment requirement to 8 bytes
(sizeof(u64)) in bpf_jit_binary_pack_alloc(). This anchors the base of
the JIT buffer to an 8-byte boundary, allowing the relative padding math
in build_plt() to correctly align the target field. |
| In the Linux kernel, the following vulnerability has been resolved:
PCI: dwc: ep: Flush MSI-X write before unmapping its ATU entry
Endpoint drivers use dw_pcie_ep_raise_msix_irq() to raise an MSI-X
interrupt to the host using a writel(), which generates a PCI posted write
transaction. There's no completion for posted writes, so the writel() may
return before the PCI write completes. dw_pcie_ep_raise_msix_irq() also
unmaps the outbound ATU entry used for the PCI write, so the write races
with the unmap.
If the PCI write loses the race with the ATU unmap, the write may corrupt
host memory or cause IOMMU errors, e.g., these when running fio with a
larger queue depth against nvmet-pci-epf:
arm-smmu-v3 fc900000.iommu: 0x0000010000000010
arm-smmu-v3 fc900000.iommu: 0x0000020000000000
arm-smmu-v3 fc900000.iommu: 0x000000090000f040
arm-smmu-v3 fc900000.iommu: 0x0000000000000000
arm-smmu-v3 fc900000.iommu: event: F_TRANSLATION client: 0000:01:00.0 sid: 0x100 ssid: 0x0 iova: 0x90000f040 ipa: 0x0
arm-smmu-v3 fc900000.iommu: unpriv data write s1 "Input address caused fault" stag: 0x0
Flush the write by performing a readl() of the same address to ensure that
the write has reached the destination before the ATU entry is unmapped.
The same problem was solved for dw_pcie_ep_raise_msi_irq() in commit
8719c64e76bf ("PCI: dwc: ep: Cache MSI outbound iATU mapping"), but there
it was solved by dedicating an outbound iATU only for MSI. We can't do the
same for MSI-X because each vector can have a different msg_addr and the
msg_addr may be changed while the vector is masked.
[bhelgaas: commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
cxl/mbox: validate payload size before accessing contents in cxl_payload_from_user_allowed()
cxl_payload_from_user_allowed() casts and dereferences the input
payload without first verifying its size. When a raw mailbox command
is sent with an undersized payload (ie: 1 byte for CXL_MBOX_OP_CLEAR_LOG,
which expects a 16-byte UUID), uuid_equal() reads past the allocated buffer,
triggering a KASAN splat:
BUG: KASAN: slab-out-of-bounds in memcmp+0x176/0x1d0 lib/string.c:683
Read of size 8 at addr ffff88810130f5c0 by task syz.1.62/2258
CPU: 2 UID: 0 PID: 2258 Comm: syz.1.62 Not tainted 6.19.0-dirty #3 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0xab/0xe0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xce/0x650 mm/kasan/report.c:482
kasan_report+0xce/0x100 mm/kasan/report.c:595
memcmp+0x176/0x1d0 lib/string.c:683
uuid_equal include/linux/uuid.h:73 [inline]
cxl_payload_from_user_allowed drivers/cxl/core/mbox.c:345 [inline]
cxl_mbox_cmd_ctor drivers/cxl/core/mbox.c:368 [inline]
cxl_validate_cmd_from_user drivers/cxl/core/mbox.c:522 [inline]
cxl_send_cmd+0x9c0/0xb50 drivers/cxl/core/mbox.c:643
__cxl_memdev_ioctl drivers/cxl/core/memdev.c:698 [inline]
cxl_memdev_ioctl+0x14f/0x190 drivers/cxl/core/memdev.c:713
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x18e/0x210 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_syscall_64+0xa8/0x330 arch/x86/entry/syscall_64.c:94
entry_SYSCALL_64_after_hwframe+0x77/0x7f
RIP: 0033:0x7fdaf331ba79
Code: ff ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 a8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fdaf1d77038 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007fdaf3585fa0 RCX: 00007fdaf331ba79
RDX: 00002000000001c0 RSI: 00000000c030ce02 RDI: 0000000000000003
RBP: 00007fdaf33749df R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fdaf3586038 R14: 00007fdaf3585fa0 R15: 00007ffced2af768
</TASK>
Add 'in_size' parameter to cxl_payload_from_user_allowed() and validate
the payload is large enough. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: always walk all pending catchall elements
During transaction processing we might have more than one catchall element:
1 live catchall element and 1 pending element that is coming as part of the
new batch.
If the map holding the catchall elements is also going away, its
required to toggle all catchall elements and not just the first viable
candidate.
Otherwise, we get:
WARNING: ./include/net/netfilter/nf_tables.h:1281 at nft_data_release+0xb7/0xe0 [nf_tables], CPU#2: nft/1404
RIP: 0010:nft_data_release+0xb7/0xe0 [nf_tables]
[..]
__nft_set_elem_destroy+0x106/0x380 [nf_tables]
nf_tables_abort_release+0x348/0x8d0 [nf_tables]
nf_tables_abort+0xcf2/0x3ac0 [nf_tables]
nfnetlink_rcv_batch+0x9c9/0x20e0 [..] |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nf_tables: unconditionally bump set->nelems before insertion
In case that the set is full, a new element gets published then removed
without waiting for the RCU grace period, while RCU reader can be
walking over it already.
To address this issue, add the element transaction even if set is full,
but toggle the set_full flag to report -ENFILE so the abort path safely
unwinds the set to its previous state.
As for element updates, decrement set->nelems to restore it.
A simpler fix is to call synchronize_rcu() in the error path.
However, with a large batch adding elements to already maxed-out set,
this could cause noticeable slowdown of such batches. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: add chann_lock to protect ksmbd_chann_list xarray
ksmbd_chann_list xarray lacks synchronization, allowing use-after-free in
multi-channel sessions (between lookup_chann_list() and ksmbd_chann_del).
Adds rw_semaphore chann_lock to struct ksmbd_session and protects
all xa_load/xa_store/xa_erase accesses. |
