| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
strparser: make sure __strp_recv isn't running before tearing down the parser
The comment above strp_done() claims that if strp is stopped,
strp_recv will no longer be called. That's only true if the caller has
a mechanism (eg locking) to guarantee that strp_recv() calls that
started before strp_stop() have completed by the time we call
strp_done().
This adds a dummy lock_sock/release_sock pair to guarantee that any
in-flight strp_recv() (which runs under either bh_lock_sock or
lock_sock, depending if it's called from ->sk_data_ready or strp_work)
has completed.
Only espintcp can be affected by this race condition, but this patch
makes sure no future user of strp can have the bug.
This could crash on strp->sk ("general mode" of strp), but this mode
has been here for 9 years and has never been used. It'll be gone soon,
no point worrying about it.
Switch the stopped/paused/etc bits to u8's to avoid races between
strp_stop() and strp_pause/unpause().
A reproducer has been published and turns the possible UAF into an
exploit [1]. |
| In the Linux kernel, the following vulnerability has been resolved:
EDAC/altera: Fix use-after-free in error paths
In both altr_edac_a10_device_add() and altr_portb_setup(), the error path
freed the dci structure before releasing the devres group. Since the managed
single and double bit IRQ handlers use altdev(dci->pvt_info) as their data, an
IRQ firing between freeing dci and unregistering the IRQs could dereference
the freed memory.
Release the devres group first so the managed IRQs are unregistered
before the dci structure is freed. |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: don't enable large folios on encrypted inodes
Commit 709f0f1f1bf5 ("ext4: add checks for large folio
incompatibilities when BS > PS") disables large folios at mount time
if the "encrypt" feature is set. However, enabling that feature on a
mounted filesystem circumvents that check, and writing encrypted data
results in a crash:
BUG: kernel NULL pointer dereference, address: 0000000000000028
Workqueue: ext4-rsv-conversion ext4_end_io_rsv_work
RIP: 0010:ext4_finish_bio+0xf7/0x3e0
Call Trace:
ext4_release_io_end+0x51/0x110
ext4_end_io_end+0x4c/0xe0
ext4_end_io_rsv_work+0xb3/0x100
Fix this by disabling large folios on encrypted inodes, as is
already done for inodes that use data journaling.
This affects all kernels between v6.19 and v7.2, but it is not needed
in v7.3, where the code was significantly refactored. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix xattr replace when multiple xattrs are packed in the same item
If we have a btrfs_dir_item item that packs multiple xattrs and then we
replace the value of one of them (with the setxattr(2) family of syscalls)
with another value of a different size, we end up not having a fully
initialized btrfs_dir_item, resulting in a corruption that the tree
checker will detect at extent buffer writeback time.
This is because in btrfs_setxattr() when we find a btrfs_dir_item with
multiple xattrs (due to the crc32c hash of their name being the same)
we delete one of the xattr items (btrfs_dir_item) and then insert a new
one, but the deletion and insertion results in shifting existing data in
the leaf and therefore when the new value of a xattr has a different size,
the new btrfs_dir_item is placed in a leaf section that was not
initialized and we only copy the value's data and set the value's length
in the new btrfs_dir_item, without setting the name, the name's length,
the key (which must be all zeroes for xattrs), flags (BTRFS_FT_XATTR) and
transaction ID.
The following script reproduces the issue:
$ cat test.sh
#!/bin/bash
DEV=/dev/sdi
MNT=/mnt/sdi
mkfs.btrfs -f $DEV
mount $DEV $MNT
touch $MNT/testfile
# Add two xattrs that, on btrfs, have the same hash (crc32c) for their
# name and therefore are packed into the same btrfs_dir_item.
setfattr -n user.foobar -v 123 $MNT/testfile
setfattr -n user.WvG1c1Td -v qwerty $MNT/testfile
# Verify the xattrs are present.
echo "xattrs before:"
getfattr --absolute-names --dump $MNT/testfile
# Now replace the value of the foobar xattr with a significantly larger
# value.
setfattr -n user.foobar -v abcdefghijklmnopqrstuvwxyz $MNT/testfile
# Check the xattrs have the expected values.
echo "xattrs after:"
getfattr --absolute-names --dump $MNT/testfile
umount $MNT
Running it:
$ ./test.sh
(...)
xattrs before:
# file: /mnt/sdi/testfile
user.WvG1c1Td="qwerty"
user.foobar="123"
xattrs after:
# file: /mnt/sdi/testfile
user.WvG1c1Td="qwerty"
So the "user.foobar" xattr is missing and there was a transaction abort
when unmounting the fs with the following traces in dmesg:
$ dmesg
[869800.159271] BTRFS warning (device sdi): access to eb bytenr 30474240 len 16384 out of range start 16015 len 25964
[869800.159293] ------------[ cut here ]------------
[869800.159296] WARNING: fs/btrfs/extent_io.c:4408 at report_eb_range+0x44/0x60 [btrfs], CPU#8: getfattr/2605179
[869800.168961] Modules linked in: btrfs dm_thin_pool (...)
[869800.190527] CPU: 8 UID: 0 PID: 2605179 Comm: getfattr Tainted: G W 7.3.0-rc3-btrfs-next-244+ #1 PREEMPT(full)
[869800.193726] Tainted: [W]=WARN
[869800.194502] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[869800.197576] RIP: 0010:report_eb_range+0x44/0x60 [btrfs]
[869800.198985] Code: 48 8b 7b 18 (...)
[869800.203531] RSP: 0018:ffffce4541937d58 EFLAGS: 00010246
[869800.204609] RAX: 0000000000000000 RBX: ffff8dde054b8738 RCX: 0000000000000000
[869800.206137] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffc04c92a0
[869800.207645] RBP: 0000000000003e8f R08: 0000000000000000 R09: 3fffffffffefffff
[869800.226175] R10: ffffce4541937a88 R11: 0000000000000003 R12: 000000000000656c
[869800.227594] R13: ffff8dde14be800f R14: 000000000000656c R15: 0000000000000069
[869800.229097] FS: 00007f59023bb780(0000) GS:ffff8de5788ed000(0000) knlGS:0000000000000000
[869800.231137] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[869800.232321] CR2: 0000558dc45e6a78 CR3: 0000000765b16004 CR4: 0000000000370ef0
[869800.233783] Call Trace:
[869800.234330] <TASK>
[869800.234791] read_extent_buffer+0x4d/0x100 [btrfs]
[869800.235898] btrfs_listxattr+0x199/0x240 [btrfs]
[869800.236912] vfs_listxattr+0x51/0
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: don't inherit MNT_UMOUNT in clone_mnt()
MNT_UMOUNT gets raised on a mount that umount_tree() or umount_one() has
taken out of its namespace. It's never cleared. __detach_mounts()
unhooks a mount that carries it instead of unmounting it.
disconnect_mount() lets an unmounted child stay attached only if its
parent carries it. propagate_umount() takes it as the sign that a mount
is going to be unmounted when it decides what else can be unmounted,
where a chain of locked mounts ends and where a for reparenting an
overmount.
clone_mnt() copies the flags of the source and only masks
MNT_INTERNAL_FLAGS which doesn't include MNT_UMOUNT. A mount that was
lazily unmounted but is kept alive by a file descriptor can still be
copied when its root is an nsfs or pidfs file because may_copy_tree()
accepts those before checking whether the source is mounted at all:
mount --bind /proc/self/ns/net /tmp/x
exec 3< /tmp/x
umount -l /tmp/x
mount --bind /proc/self/fd/3 /tmp/y
The mount on /tmp/y is attached to the caller's namespace with
MNT_UMOUNT already set and every copy of it inherits the flag again.
That causes a number of bugs:
- Unlink its mountpoint from a mount namespace where it isn't one.
__detach_mounts() takes it for a mount that was unmounted earlier,
unhooks it from its parent and drops the reference the namespace
holds on it. It stays in the namespace with one reference too few
and as its own parent, so it can't be unmounted through the file
descriptor anymore and the namespace never finds it again. When the
namespace goes away it's leaked and points to a freed struct
mnt_namespace that may_change_propagation() and anon_ns_root() read
on the next propagation change or mount_setattr() through the file
descriptor.
- Make it shared and unmount a peer. trace_transfers() follows the
flag from the peer into it and strips it from its peer group.
- Let a propagated umount reach it. gather_candidates() marks it with
T_UMOUNT_CANDIDATE but never puts it on the candidate list, so the
mark is never cleared and every later propagated umount skips it. If
it's the parent of a locked mount handle_locked() takes it as the
cutoff and commits the locked child that should have stayed and
disconnect_mount() leaves that child attached to it, unmounted under
a mounted parent, which is what disconnect_mount() exists to
prevent. When the namespace goes away umount_tree() visits the child
a second time. And once __detach_mounts() has made it its own parent
reparent() never finds the end of the chain of unmounted parents.
A clone is a new mount that has never been unmounted. Add MNT_UMOUNT
to MNT_INTERNAL_FLAGS so clone_mnt() never copies it. And warn when
umount_tree() reaches a mount that already has it set. |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: reset the old parent's ->overmount in mnt_change_mountpoint()
__umount_mnt() resets ->overmount of the parent when it unmounts the
mount that overmounts it. mnt_change_mountpoint() doesn't. It moves the
mount to its new parent and leaves the old one pointing at it.
For a mount that is moved beneath in attach_recursive_mnt() that doesn't
matter. The new mount has already reset ->overmount of the old parent by
the time the old top mount is moved onto it.
It matters for reparent() though. propagate_umount() moves a surviving
overmount onto the first ancestor that isn't going to be unmounted. The
mount it was taken from is unmounted immediately afterwards. If a file
descriptor keeps that unmounted mount alive ->overmount points at the
moved mount. That's a dangling pointer and UAF as the moved mount is
unmounted and freed.
do_lock_mount() follows ->overmount from the target path under
mount_lock. With a file descriptor on such a mount as the target of a
mount beneath topmost_overmount() walks into the freed mount and
do_lock_mount() takes references on whatever it finds there.
So reset ->overmount of the old parent in mnt_change_mountpoint() the
same way __umount_mnt() does. A mount's ->overmount is then always a
mount that is attached to it. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe: Fix stale pinned_link entry when fb-pin performs the final unpin
xe_bo_pin_external() and xe_bo_unpin_external() maintain the bo's
pinned_link list membership in xe->pinned.late.external, based on
whether the current call is the outermost pin or the final unpin.
However, the same external bo's pin_count can also be raised and
lowered directly by __xe_pin_fb_vma()/__xe_unpin_fb_vma(), which pin
the bo as a display scanout buffer without going through
xe_bo_pin_external()/xe_bo_unpin_external() at all, and have no
notion of, or ownership over, pinned_link.
If a bo is pinned both externally (e.g. dma-buf export) and as an fb,
and the external unpin happens first, xe_bo_unpin_external() correctly
observes pin_count > 1 and leaves the bo on pinned_link. When the fb
unpin later performs the true last unpin (pin_count 1 -> 0), it never
touches pinned_link, leaving the bo linked on xe->pinned.late.external
indefinitely. Once the bo is subsequently freed, this stale list entry
points into freed memory, corrupting the list and risking a
use-after-free the next time the list is walked or spliced.
The backup object pin/unpin sites in xe_bo_notifier_prepare_pinned()/
xe_bo_notifier_unprepare_pinned() have the same bypass characteristic,
though they never add their bo to a pinned list, so are not affected
by this particular list-corruption issue.
Move the pinned_link removal into xe_bo_account_unpin(), which already
runs on every unpin path (kernel, external, framebuffer, backup
object) right before the true 1 -> 0 pin_count transition. Since
list_del_init() only operates on the node itself, this removal is
list-agnostic and safe to perform regardless of which list (external
or kernel_bo_present) the bo happens to be linked on, or which code
path is performing the final unpin. Drop the now-redundant explicit
list_del_init() calls in xe_bo_unpin_external() and xe_bo_unpin().
v2:
- New patch
v3:
- Rebased on changes to previous patch.
(cherry picked from commit ca58d36a1f93af586ee93b340c9f9fd81312cc01) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915/gem: Prevent overstepping exec array boundary
It is possible for eb_relocate_parse_slow() to call kvfree() on
entries outside the original exec array during following
scenario inside eb_relocate_parse_slow():
1) eb_copy_relocations() allocates as many as eb->buffer_count
copies for exec entries;
2) eb_parse() appends up to two VMAs, right after incrementing
eb->buffer_count;
3) cleanup under "out" label uses this incremented buffer_count
to release relocation pointers from exec array via kvfree(),
not from VMA array.
To amend this problem, ensure that relocation cleanup uses the
original exec object count, excluding the VMAs appended by the
command parser.
(cherry picked from commit 2a0158925fb943c7ba8f3216e2734952128defc9) |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Prevent stale XSK buffer release on MPWQE refill retry
With AF_XDP on a striding RQ, mlx5e defers releasing XSK buffers until
an MPWQE is refilled. If XSK allocation then returns -ENOMEM,
actual_wq_head is not advanced and a later NAPI poll retries the same
WQE.
mlx5e_free_rx_mpwqe() leaves each released slot marked as releasable. On
retry it can therefore call xsk_buff_free() again through stale pointers
after the frames have returned to the XSK pool and been reallocated.
Set all skip_release_bitmap bits in the common error path of
mlx5e_xsk_alloc_rx_mpwqe(). This matches mlx5e_alloc_rx_mpwqe(). A
successful allocation already clears the bitmap after replacing every
buffer, so retries become idempotent without changing the success path.
Fault injection forced three consecutive failures for one selected MPWQE.
Both an early allocation failure and a partial 8-of-16-buffer unwind
released the original 16 XSK buffers only once. Each error left a full
bitmap, the following NAPI retry skipped the release, and a later
successful allocation cleared it. A 20-second AF_XDP zero-copy pressure
run exercised 1,575,262 buffer allocation failures without invalid
descriptors, WQE errors, or kernel warnings. |
| In the Linux kernel, the following vulnerability has been resolved:
drop_monitor: fix out-of-bounds write in reset_per_cpu_data()
In reset_per_cpu_data(), al is computed as:
al = sizeof(struct net_dm_alert_msg);
al += dm_hit_limit * sizeof(struct net_dm_drop_point);
al += sizeof(struct nlattr);
skb = genlmsg_new(al, GFP_KERNEL);
...
nla = nla_reserve(skb, NLA_UNSPEC, sizeof(struct net_dm_alert_msg));
...
msg = nla_data(nla);
memset(msg, 0, al);
Because al includes sizeof(struct nlattr) (the 4-byte attribute header),
genlmsg_new() allocates al bytes of tailroom starting at nla.
However, msg points to nla_data(nla), which is located
sizeof(struct nlattr) bytes past nla. Calling memset(msg, 0, al)
therefore writes al bytes starting from msg, exceeding the allocated
buffer by sizeof(struct nlattr) (4 bytes) and corrupting
skb_shared_info.
Fix this by letting al represent only the payload length, allocating
the skb with genlmsg_new(nla_total_size(al), GFP_KERNEL), and zeroing
al bytes from msg. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: alps: fix use-after-free on input2 registration failure
alps_input_configured() stores data->input2 before calling
input_register_device(). If registration fails, input_free_device()
frees the input device but data->input2 still points to the freed memory.
alps_input_configured() calls hid_hw_open() before allocating input2, so
URBs are already active and raw_event can fire during the failure window.
A U1_SP_ABSOLUTE_REPORT_ID report arriving then causes u1_raw_event()
to dereference the freed data->input2 -> use-after-free.
Fix by only storing input2 into drvdata after successful registration
and adding a NULL guard in the raw_event path. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fs/xattr: don't assume the inode is locked in path_unlink/path_rmdir
bpf_lsm_has_d_inode_locked() makes the verifier rewrite
bpf_[set|remove]_dentry_xattr() to the _locked variants, which assume
that the caller already holds the inode's i_rwsem. The path_unlink and
path_rmdir hooks are listed, but security_path_unlink() and
security_path_rmdir() run before vfs_unlink()/vfs_rmdir() take the
victim inode's i_rwsem, so a sleepable BPF LSM program attached to
either hook mutates the victim's xattrs without the lock held.
Drop the two path hooks from d_inode_locked_hooks so that the verifier
keeps the locking bpf_[set|remove]_dentry_xattr() variants, which take
the lock themselves. |
| In the Linux kernel, the following vulnerability has been resolved:
amt: send the relay's General Query directly from the receive path
An skb queued in a qdisc can outlive the tunnel it references
through a raw pointer in skb->cb. For example, with igmp_qrv set
to 1 on the relay a tunnel lives for 135s, so a netem delay of
180s on the amt device outlives it; when the tunnel expires and is
freed, the subsequent dequeue triggers a use-after-free in
amt_dev_xmit().
BUG: KASAN: slab-use-after-free in amt_dev_xmit+0x2763/0x2e20
Call Trace:
amt_dev_xmit+0x2763/0x2e20 [drivers/net/amt.c:1262]
dev_hard_start_xmit+0x22f/0x620
sch_direct_xmit+0x12e/0xac0
netem_dequeue+0x333/0xc50
net_tx_action+0x35c/0xa60
amt_send_igmp_gq() and amt_send_mld_gq() are only called from
amt_request_handler(), inside the rcu_read_lock_bh() section of
amt_rcv(). amt_request_handler() already has the tunnel the query is
for: it found or created it inside that section. Queuing the query with
dev_queue_xmit() only leads back into amt_dev_xmit(), which strips the
Ethernet header and calls amt_send_membership_query() for that tunnel.
Make that call directly from the two senders instead, the same way
amt_send_advertisement() transmits from the receive path. The query
never waits in a qdisc, the tunnel is only dereferenced inside the
RCU section that found or created it, and nothing is stored in
skb->cb, so no lookup or refcount is needed. Remove the query branch
of amt_dev_xmit(), amt_skb_cb() and struct amt_skb_cb, which have no
users left.
Behaviour changes:
- The relay's own General Queries no longer pass through the amt
device's egress path: its qdisc, tc egress (clsact/tcx), the
netfilter egress hook and packet taps. They are still visible as
UDP on the underlay.
- A query that is sent successfully is no longer counted as
tx_dropped. The old query branch left through the unlock label,
which counted every sent query as dropped.
- A query that reaches amt_dev_xmit() on a relay from elsewhere,
such as a userspace querier, is now dropped at the IGMP/MLD type
switch. Before, it trusted whatever skb->cb held, and a NULL
tunnel hit the WARN_ON(1). |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: never expire a locked mount
Locked mounts are special. They protect the underlying files and
directories from being revealed. do_umount() refuses to unmount locked
mounts but shrink_submounts() doesn't.
A shrinkable mount can become locked once the owner of a user namespace
puts it beneath a locked mount with MOVE_MOUNT_BENEATH. The locked
property now moves to the mount at the bottom making it possible to
unmount the top mount.
So umount() of an unlocked ancestor now expires the bottom mount first
and the covered directory is revealed:
move_mount(c -> x/hidden, MOVE_MOUNT_BENEATH) = 0
the cover after the lock moved: umount2(x/hidden) = 0
the holder of the lock: umount2(x/hidden) = EINVAL
the root of the copy, busy: umount2(x) = EBUSY
reads x/hidden/secret: "covered-by-root"
So leave a locked mount alone as it dies together with its parent. A
plain umount() of an unlocked mount with a locked one below it is EBUSY
from now on. It's the same for any other locked child. A lazy umount
still takes the whole tree.
mark_mounts_for_expiry() never sees a locked mount. lock_mnt_tree()
leaves a mount on an expiry list alone and nothing else puts a locked
one on such a list. Add an assert for this. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: libiscsi_tcp: Check the data direction of a Data-In PDU
The Data-In branch of iscsi_tcp_hdr_dissect() resolves the ITT to a task
and copies the PDU's data segment into that command's scatterlist without
asking whether the command was reading. iscsi_tcp_r2t_rsp() in the same
file does ask, and rejects an R2T for a command that is not DMA_TO_DEVICE.
A target that answers a WRITE command's ITT with a Data-In therefore has
the initiator write target-supplied bytes into the pages that write was
about to send. Those are the caller's own pinned pages for an O_DIRECT
write, and page cache pages for a buffered one.
Observed against a test target that emits one 512-byte Data-In naming a 128
KB write's ITT, after the R2T for that write. With O_DIRECT the caller's
buffer ends up holding 512 bytes of the target's data while pwrite()
returns 131072. Buffered is quieter: pwrite() and fsync() both succeed,
nothing is logged, and reading those blocks back returns the target's bytes
out of the page cache without a command going on the wire.
Check the direction before using the scatterlist, the way the R2T path
already does. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Skip unsettled links in link iterator
bpf_link_prime() inserts a link into link_idr before anon_inode_getfile()
succeeds and before bpf_link_settle() publishes the ID in link->id.
bpf_link_by_id() treats such an ID-zero link as unsettled, but the link
iterator takes a reference without this check.
If anon_inode_getfile() then fails, the creator removes the ID and frees
its still-private link directly. The iterator is left with a dangling
reference and its next bpf_link_put() accesses freed memory.
Treat ID-zero entries as transient in bpf_link_get_curr_or_next(), just as
bpf_link_by_id() does.
BUG: KASAN: slab-use-after-free in bpf_link_put
Write of size 8 by task exp/384
Call Trace:
bpf_link_put kernel/bpf/syscall.c:3372
bpf_link_seq_next kernel/bpf/link_iter.c:33
bpf_seq_read kernel/bpf/bpf_iter.c:158
vfs_read fs/read_write.c:572
ksys_read fs/read_write.c:716
do_syscall_64 arch/x86/entry/syscall_64.c:84
entry_SYSCALL_64_after_hwframe arch/x86/entry/entry_64.S:121
Kernel panic - not syncing: KASAN: panic_on_warn set ... |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: fix swapped IPv6 IPsec policy masks
IPv6 XFRM policies may use different source and destination prefix
lengths. mlx5e_ipsec_policy_mask() builds the corresponding masks
independently, but setup_fte_addr6() installs each mask in the opposite
address field.
When the prefix lengths differ, this makes the source match use the
destination prefix and the destination match use the source prefix. The
resulting hardware rule can both miss traffic covered by the policy and
match traffic outside it.
Install each mask in its corresponding match field. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/nouveau/uvmm: fix UAF in nouveau_uvmm_sm when BO is in TTM_PL_SYSTEM
nouveau_uvmm_sm() calls op_map(), which passes bo->resource through
nouveau_mem() to nouveau_uvma_map(). nouveau_uvmm_vmm_map() then reads
mem->mem.type.
But this is only valid when bo->resource is backed by struct nouveau_mem,
as is the case for VRAM and TT resources. If the BO is left in
TTM_PL_SYSTEM, bo->resource is only a struct ttm_resource. Treating it
as struct nouveau_mem makes the mem->mem.type read past the end of the
resource, causing a KASAN: slab-use-after-free Read in nouveau_uvmm_sm
report:
BUG: KASAN: slab-use-after-free in nouveau_uvmm_vmm_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:152 [inline]
BUG: KASAN: slab-use-after-free in nouveau_uvma_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:199 [inline]
BUG: KASAN: slab-use-after-free in op_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:849 [inline]
BUG: KASAN: slab-use-after-free in nouveau_uvmm_sm.constprop.0+0x6ab/0x900 drivers/gpu/drm/nouveau/nouveau_uvmm.c:903
Read of size 1 at addr ffff888127d3e3a0 by task kworker/0:1/11
CPU: 0 UID: 0 PID: 11 Comm: kworker/0:1 Not tainted 7.2.0 #5 PREEMPT(lazy)
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.16.3-debian-1.16.3-2 04/01/2014
Workqueue: nouveau_sched_wq_2224 drm_sched_run_job_work
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:94 [inline]
dump_stack_lvl+0x95/0xe0 lib/dump_stack.c:120
print_address_description mm/kasan/report.c:378 [inline]
print_report+0xcb/0x5a0 mm/kasan/report.c:482
kasan_report+0xca/0x100 mm/kasan/report.c:595
nouveau_uvmm_vmm_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:152 [inline]
nouveau_uvma_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:199 [inline]
op_map drivers/gpu/drm/nouveau/nouveau_uvmm.c:849 [inline]
nouveau_uvmm_sm.constprop.0+0x6ab/0x900 drivers/gpu/drm/nouveau/nouveau_uvmm.c:903
nouveau_uvmm_sm_unmap drivers/gpu/drm/nouveau/nouveau_uvmm.c:932 [inline]
nouveau_uvmm_bind_job_run+0xd6/0x250 drivers/gpu/drm/nouveau/nouveau_uvmm.c:1532
nouveau_job_run drivers/gpu/drm/nouveau/nouveau_sched.c:350 [inline]
nouveau_sched_run_job+0x62/0xd0 drivers/gpu/drm/nouveau/nouveau_sched.c:364
drm_sched_run_job_work+0x356/0xa10 drivers/gpu/drm/scheduler/sched_main.c:1061
process_one_work+0x8a5/0x1900 kernel/workqueue.c:3322
process_scheduled_works kernel/workqueue.c:3405 [inline]
worker_thread+0x5dd/0xd80 kernel/workqueue.c:3486
kthread+0x31d/0x420 kernel/kthread.c:436
ret_from_fork+0x662/0x940 arch/x86/kernel/process.c:158
ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:245
</TASK>
Allocated by task 2224 on cpu 0 at 66.550027s:
kasan_save_stack+0x24/0x50 mm/kasan/common.c:57
kasan_save_track+0x17/0x60 mm/kasan/common.c:78
poison_kmalloc_redzone mm/kasan/common.c:398 [inline]
__kasan_kmalloc+0xaa/0xb0 mm/kasan/common.c:415
kasan_kmalloc include/linux/kasan.h:263 [inline]
__do_kmalloc_node mm/slub.c:5334 [inline]
__kmalloc_noprof+0x304/0x7c0 mm/slub.c:5359
_kmalloc_noprof include/linux/slab.h:992 [inline]
dma_resv_list_alloc+0x27/0x90 drivers/dma-buf/dma-resv.c:106
dma_resv_reserve_fences+0x60e/0xa30 drivers/dma-buf/dma-resv.c:205
ttm_bo_alloc_resource+0x12c/0xbd0 drivers/gpu/drm/ttm/ttm_bo.c:721
ttm_bo_validate+0x1bc/0x4a0 drivers/gpu/drm/ttm/ttm_bo.c:856
ttm_bo_init_reserved+0x2c3/0x570 drivers/gpu/drm/ttm/ttm_bo.c:970
nouveau_bo_init+0x159/0x2c0 drivers/gpu/drm/nouveau/nouveau_bo.c:359
nouveau_gem_new+0x234/0x5f0 drivers/gpu/drm/nouveau/nouveau_gem.c:272
nouveau_gem_ioctl_new+0x1eb/0x420 drivers/gpu/drm/nouveau/nouveau_gem.c:352
drm_ioctl_kernel+0x192/0x350 drivers/gpu/drm/drm_ioctl.c:817
drm_ioctl+0x4f8/0xb40 drivers/gpu/drm/drm_ioctl.c:914
nouveau_drm_ioctl+0xea/0x2c0 drivers/gpu/drm/nouveau/nouveau_drm.c:1338
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x180/0x1d0 fs/ioctl.c:583
do_syscall_x64 ar
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sync: Fix command skb lifetime during scan setup
During PA sync scan setup, hci_le_set_ext_scan_param_sync() gets the
address used for the PA_LINK lookup from hci_sent_cmd_data(). The
returned pointer borrows storage from sent_cmd or req_skb, without
holding a reference to either skb.
The scan worker runs on req_workqueue while hci_cmd_work() runs on the
separate device workqueue. After the scan worker loads sent_cmd, the
command worker can free and replace it before hci_sent_cmd_data()
dereferences the skb. The command payload can also be freed between
returning from the helper and comparing the address. The connection
lookup's RCU critical section does not protect the command skb.
KASAN reported:
BUG: KASAN: slab-use-after-free in hci_sent_cmd_data+0x27c/0x2f0
Workqueue: hci0 hci_cmd_sync_work
Call Trace:
hci_sent_cmd_data+0x27c/0x2f0
hci_le_set_scan_param_sync+0x43a/0x850
hci_passive_scan_sync+0xb09/0x1460
hci_update_passive_scan_sync+0x47c/0x6e0
hci_le_pa_create_sync+0x200/0xa70
hci_cmd_sync_work+0x13c/0x290
Allocated by task 95:
skb_clone+0x13f/0x340
hci_cmd_work+0x2a9/0x7e0
Freed by task 95:
kmem_cache_free+0xba/0x3a0
hci_cmd_work+0x29c/0x7e0
Use hdev->lock to serialize the address snapshot with sent_cmd
replacement. Protect req_skb replacement and completion cleanup with
the same lock because the helper falls back to that skb. Copy the
address before releasing the lock and use the copy for the existing
RCU-protected connection lookup. Release the mutex before sending or
waiting for commands, preserving the lookup and completion ordering. |
| In the Linux kernel, the following vulnerability has been resolved:
gve: fix XSK buffer leak on error descriptor
When the error bit is set in the RX completion descriptor, the buf_state
and its attached buffer should be freed. In the case of AF_XDP ZC, the
XSK buffer was not freed, leading to a leak.
This issue was caught by LLM. |
