| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
spi: davinci: switch to managed controller allocation
The controller is allocated with the non-managed spi_alloc_host() while
the interrupt is registered with devm_request_threaded_irq(). During
removal, spi_bitbang_stop() only unregisters the controller; the
subsequent spi_controller_put() then frees the controller together with
its embedded davinci_spi devdata, which is the IRQ handler's dev_id.
The devm_request_threaded_irq() release action (free_irq()), which
drains the handler, does not run until after .remove() returns. A late
or latched interrupt can therefore reach davinci_spi_irq() and
dereference already-freed memory.
Switch to devm_spi_alloc_host() so that the devres LIFO order releases
the controller only after free_irq() has drained the handler, and drop
the now-redundant spi_controller_put() from .remove(). The probe error
path is simplified to direct returns.
The clock is acquired with devm_clk_get_enabled(), which is registered
after the IRQ and thus released before it by the devres LIFO order.
Drain the interrupt explicitly with devm_free_irq() before disabling the
controller so that a late interrupt cannot access the registers of a
clock-gated controller.
This issue was found by an in-house static analysis tool. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix overreads in ath11k_wmi_process_csa_switch_count_event()
There is no policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT, so
the parse infrastructure does not enforce a minimum length for the event
struct. Additionally, the num_vdevs field is taken directly from firmware
and used as a loop bound over the vdev_ids array without checking that it
fits within the TLV payload. Either condition can cause an out-of-bounds
read.
Add a TLV policy entry for WMI_TAG_PDEV_CSA_SWITCH_COUNT_STATUS_EVENT so
the parse infrastructure enforces a minimum length for the fixed-size event
struct. Add a helper ath11k_wmi_tlv_data_len() to recover the payload
length of a parsed TLV from the header preceding its data pointer. Use it
in ath11k_wmi_process_csa_switch_count_event() to bound num_vdevs before
the loop.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix stride mismatch in mac_phy_caps_parse()
Currently, in ath11k_wmi_tlv_mac_phy_caps_parse(), kcalloc() sizes the
mac_phy_caps buffer as tot_phy_id * len, where len is clamped to
min(firmware_len, sizeof(struct wmi_mac_phy_capabilities)). The subsequent
memcpy() destination advances by sizeof(full struct) per slot via C
pointer arithmetic, not by the clamped len. When firmware sends short
TLVs, the second and later slots are written past the end of the
allocation.
The reader in ath11k_pull_mac_phy_cap_svc_ready_ext() also indexes the
buffer with full-struct pointer arithmetic, so the allocation must match
that stride.
Fix by using kzalloc_objs(), which derives the element size from the
pointer type, making allocation size and pointer stride provably
consistent regardless of what len the firmware provides.
Compile tested only. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Fix potential UAF when reading bpf link info
In bpf_link_show_fdinfo and bpf_link_get_info_by_fd, link->prog is
accessed without holding any locks. If the prog is concurrently replaced
via bpf_link_update, the old prog can be freed, leading to a potential
UAF issue.
Fix this by accessing link->prog under RCU protection to safely fetch
the pointer and guarantee its lifetime while reading its fields. |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid1: create serial pool adding rdev to array with serialize_policy=1
The following bug has been observed with kernel 7.1.3 after adding a new
rdev to an existing RAID1 array with serialize_policy enabled:
Oops: 0002 [#1]
CPU: 0 UID: 0 PID: 19639 Comm: ext4lazyinit Not tainted 7.1.3-1-default
RIP: _raw_spin_lock_irqsave+0x27/0x50
CR2: 0000000000004960
Call Trace:
wait_for_serialization+0xb9/0x260 [raid1]
raid1_make_request+0x762/0xaff [raid1]
md_handle_request+0x1c9/0x2e0 [md_mod]
The raid1.c code calls wait_for_serialization() if the MD_SERIALIZE_POLICY
is set, and wait_for_serialization assumes that rdev->serial is
initialized. Normally this will be the case for arrays that have
the serialize_policy sysfs attribute set to 1.
But when a new rdev is added to an existing array in bind_rdev_to_array(),
the condition at mddev_create_serial_pool() causes creation of rdev->serial
to be skipped. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
misc: sgi-gru: remove interrupt-context page-table walks
The GRU TLB miss handler walks a process's page tables without holding
page-table locks or a reference to the mapped page. It also uses a kernel
page-table accessor on user page tables and supports only PMD-level large
mappings on x86-64.
Remove the direct walker. Send interrupt faults directly to user polling
mode so the existing call-OS fallback retries them in process context.
Remove the mmap-lock failure statistic that can no longer be incremented. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: fix non-AQL packet accounting for MLO stations
__mt76_tx_queue_skb() overrides the wcid passed by the driver with
sta->drv_priv, so the wcid might incorrectly be changed after TX,
causing wcid->non_aql_packets to be counted on the wrong wcid. For
example, on the AP side, if a station's setup link is the 5G link and
the station uses 2G to transmit a frame, the value of non_aql_packets
is increased on the 5G wcid but decreased on the 2G wcid. Once the
inflated counter exceeds MT_MAX_NON_AQL_PKT, the TX scheduler
permanently refuses to service the station.
Drop the reassignment and account on the wcid used for transmission.
This also records the actual wcid in the queue entry. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: unwind state on add_interface failure
When mt76_wcid_alloc() fails, mt7915_add_interface() returned without
clearing the vif_mask/omac_mask bits it had already set, without removing
the firmware dev info added earlier, and without clearing a monitor_vif
pointer to the vif mac80211 is about to free. mac80211 does not call
remove_interface() for a failed add, so the indices and firmware dev
entry leaked permanently and testmode could dereference the stale
monitor_vif. Add a proper error unwind. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: cancel reset and rc work on device unregister
Both drivers cancelled dump_work on unregister but left reset_work and
rc_work to be flushed only by destroy_workqueue() in mt76_free_device(),
which runs after the hw is unregistered and the hardware stopped. A
reset_work that fires in that window calls ieee80211_restart_hw() and
re-arms mac_work on an unregistered hw, and rc_work touches station state
being torn down. Cancel both up front, alongside dump_work. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, x86: Fix trampoline stack size for 128-bit arguments
btf_distill_func_proto() accepts a function argument up to 16 bytes, so a
128-bit scalar such as __int128 reaches the x86 trampoline with
arg_size == 16. But the current implementation assumes an __int128
argument only needs one register, so the register save area is
under-allocated and save_args() overwrites adjacent stack slots.
Compute the register count from arg_size for all arguments to fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core seccomp code, instead move the
synchronisation code into the ptrace GPR and syscall setting code so
that 'orig_x0' is kept up to date with x0 whenever we're stopped on the
syscall entry path. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: nl80211: clean up color-change beacon data on errors
nl80211_color_change() calls nl80211_parse_beacon() for the beacon_next
template, which can allocate params.beacon_next.mbssid_ies and .rnr_ies.
A parsing failure returned directly instead of using the out: cleanup,
leaking any allocations completed before the error.
Allocate the nested attribute table before parsing beacon_next. Its
allocation failure can then return before beacon data exists, while a
later parsing failure uses out: to release the parsed data. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: brcmfmac: fix P2P action frame handling without device vif
Some P2P action frame paths assume the P2P device vif is always
available. That is not true when userspace sends non-P2P public action
frames through the primary interface, or when action-frame abort runs
after the P2P device vif has not been created.
Fall back to the primary vif when aborting an action frame without a P2P
device vif, and guard P2P device saved IE access before using it for
peer channel search. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: stop PMSR before P2P and NAN teardown
PMSR request teardown must abort active measurements while the
wireless_dev is still present in the driver. cfg80211_leave_locked() and
cfg80211_stop_pd() already do this before invoking the driver's stop
callback, but cfg80211_stop_p2p_device() and cfg80211_stop_nan() do not.
Those helpers are also called directly by nl80211, rfkill shutdown, and
wireless_dev unregister paths. If one of these paths stops a P2P device
or NAN interface with a pending request, it removes the mac80211
subinterface from the driver first. Subsequent request cleanup cannot
reach the lower driver's abort callback, but cfg80211 frees the request
regardless. Driver state can then retain a stale request and use it when
it later reports a result.
Call cfg80211_pmsr_wdev_down() before stopping the P2P device or NAN
interface. This keeps lower-driver request state and cfg80211 request
ownership in sync for all of the helpers' callers. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: core: do fallible allocations before the console can be registered
serial_core_add_one_port() allocates uport->tty_groups after
uart_configure_port(), which may register the console. If the allocation
fails, the driver unwinds the port while its console remains registered.
The earlier uport->name allocation has a related failure path that leaves
state->uart_port linked to a port being freed.
Failslab reproduced a NULL dereference in PL011 console output and a KASAN
use-after-free in i.MX console output after failed binds.
Allocate the name and tty_groups before linking the port and configuring
it. Reserve space for the optional driver attribute group because
config_port() may populate uport->attr_group during configuration. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: core: clear freed pointers on uart_register_driver() failure
uart_register_driver() leaves drv->state pointing to freed memory when
tty_alloc_driver() fails. If tty_register_driver() fails, drv->tty_driver
also retains a pointer after its reference is dropped.
Drivers that use drv->state as an "already registered" flag can then skip
registration on the next probe and pass the freed state to
uart_add_one_port().
This issue was found with failslab on QEMU's raspi1ap board by
failing registration and binding the PL011 port again.
Clear both pointers on their failure paths, as uart_unregister_driver()
already does. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: skip cdev_del() when no cdev is registered
TTY device registration can fail before a cdev is allocated.
Serial core keeps the port so setserial can still use it, and later
removal passes the NULL cdev slot to cdev_del(), causing a NULL-pointer
dereference.
Only delete the cdev when the slot is not NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: logitech-hidpp: Fix FF device cleanup on init failure
hidpp_ff_init() creates the input force-feedback device with
input_ff_create(), then allocates the HID++ FF private data,
effect ID array, and workqueue.
If any of those allocations fail after input_ff_create() succeeds,
the function returns an error without destroying the FF device.
Add an unwind path that frees the private allocations made by
hidpp_ff_init() and calls input_ff_destroy() for failures after
input_ff_create() succeeds. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: steam: Reject short reads
Steam Controller FEATURE reports encode the size of the message in the
message itself. Previously we were trusting that the size reported matched
the size we actually read, leading to a potential issue with short reads.
Instead, we should actually verify the length of the read. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2/cluster: keep heartbeat local node stable
o2nm_node_local_store() handles local=0 by stopping o2net and setting
cl_local_node to O2NM_INVALID_NODE_NUM, but it leaves cl_has_local set.
That stale state makes o2nm_this_node() return 255, blocks a later local=1
attempt with -EBUSY, and can feed 255 to heartbeat users that call
o2nm_this_node() dynamically.
Clearing cl_has_local is required when the local node is reset. But
heartbeat threads can still be running at that point. They pin the local
node config item at startup, yet o2hb_do_disk_heartbeat() and thread
teardown re-read o2nm_this_node() for the local slot and for
o2nm_undepend_this_node(). Once local=0 has cleared the live local-node
state, those dynamic reads return O2NM_MAX_NODES, which is also the
invalid node number 255.
Store the local node number in the heartbeat region when the region
starts. Use that stable node for heartbeat slot writes/checks,
negotiation messages, and the final configfs undepend. Stop the heartbeat
loop when the current local node no longer matches the stored node, and
clear cl_has_local together with cl_local_node in the local=0 path so
nodemanager state matches node removal.
Validation reproduced this kernel report:
KASAN slab-out-of-bounds in o2hb_do_disk_heartbeat+0x372/0xb30
RIP: 0010:memset+0xf/0x20
Read of size 8
Call trace:
dump_stack_lvl+0x66/0xa0
print_report+0xd0/0x630
o2hb_do_disk_heartbeat+0x372/0xb30 (fs/ocfs2/cluster/heartbeat.c:1079)
srso_alias_return_thunk+0x5/0xfbef5
__virt_addr_valid+0x188/0x2f0
kasan_report+0xe4/0x120
o2hb_do_disk_heartbeat+0x5/0xb30 (fs/ocfs2/cluster/heartbeat.c:1079)
o2hb_thread+0x14e/0x770
kthread_affine_node+0x139/0x180
lockdep_hardirqs_on_prepare+0xda/0x190
trace_hardirqs_on+0x18/0x130
kthread+0x19d/0x1e0
ret_from_fork+0x37a/0x4d0
__switch_to+0x2d5/0x6f0
ret_from_fork_asm+0x1a/0x30 |
