| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| The MCTP-over-I2C+GPIO target binding in subsys/pmci/mctp/mctp_i2c_gpio_target.c emulates a small pseudo-register file, where the bus controller first writes a register number and then writes or reads payload bytes. The selected register (b->reg_addr) and the data-phase flag (b->rxtx) were never cleared when the controller issued an I2C STOP, so after a completed transfer the target still had a data register selected while the packet buffer that register refers to had already been consumed and set to NULL by mctp_i2c_gpio_target_stop().
A controller on the bus can re-enter the same branch of mctp_i2c_gpio_target_stop() with a NULL buffer using two ordinary transactions and no authentication: first a normal packet write to MCTP_I2C_GPIO_RX_MSG_ADDR followed by STOP (which delivers and frees b->rx_pkt), then a bare read transaction followed by STOP. The failing read_requested() call leaves the stale state untouched and the I2C driver still delivers the STOP callback, which then calls mctp_bus_rx() with a NULL packet. The symmetric case exists on the transmit side, where the stale MCTP_I2C_GPIO_TX_MSG_ADDR selection dereferences b->tx_pkt->end after b->tx_pkt has been cleared and additionally signals b->tx_complete a second time, causing the next outbound packet to be dropped.
The dereference happens in the I2C target interrupt handler, so on any target that traps accesses to address 0 the result is a fatal exception and a device reset or halt — a denial of service inflicted by any device able to act as controller on the shared management bus (for example compromised firmware on a peer MCTP endpoint or on the BMC). On parts where address 0 is readable, the impact degrades to a malformed packet buffer being handed to the MCTP stack and lost transmit packets. No attacker-controlled value is written and no confidentiality or integrity boundary is crossed.
The fix resets b->reg_addr to MCTP_I2C_GPIO_INVALID_ADDR and clears b->rxtx at every STOP, so a new register must be selected before any data phase can run again. Only builds that opt into the experimental CONFIG_MCTP subsystem with CONFIG_MCTP_I2C_GPIO_TARGET=y are affected. |
| Apache Traffic Server can crash with a null pointer dereference when a client POST request is torn down via half-close while a chunked origin response is being reparsed from a reentrant write-ready callback, a timing-dependent race introduced by the CVE-2021-32564 flow-control backports.
This issue affects Apache Traffic Server: 9.2.15, 10.1.4, 10.2.0.
Users are recommended to upgrade to version 9.2.16, 10.1.5, or 10.2.1, which fix the issue. |
| In the Linux kernel, the following vulnerability has been resolved:
workqueue: Fix NULL current_pwq deref in chained work check
current_wq_worker() only tells us that %current is a kworker. It does
not guarantee that the worker is currently executing a work item, as
worker->current_pwq is populated only while process_one_work() is running
the work function.
is_chained_work() can be reached while queueing on a draining or
destroying workqueue. If a kworker outside work-item execution reaches
that path, current_wq_worker() returns a worker but worker->current_pwq is
NULL, and the chained-work test can fault before it emits the intended
warning.
Guard the chained-work test with worker->current_pwq. A kworker without
current_pwq is not executing work on the target workqueue, so the helper
should return false and let the draining/destroying warning fire. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv6: sr: use skb_get_hash_net() in seg6_make_flowlabel()
Since commit d58e468b1112 ("flow_dissector: implements flow dissector
BPF hook") __skb_flow_dissect() needs a net pointer, either from
skb->dev, skb->sk, or since commit 3cbf4ffba5ee ("net: plumb network
namespace into __skb_flow_dissect") a caller provided pointer.
syzbot was able to reach seg6_make_flowlabel() with an skb having
neither skb->dev nor skb->sk set: a TIPC UDP bearer sends a discovery
message through an IPv4 route using seg6 encap, while
net.ipv6.seg6_flowlabel is set to 1.
seg6_make_flowlabel() already has a net pointer, use skb_get_hash_net().
WARNING: net/core/flow_dissector.c:1131 at __skb_flow_dissect+0x910/0x5368 net/core/flow_dissector.c:1126, CPU#0: syz.0.17/4930
Call trace:
__skb_flow_dissect+0x910/0x5368 net/core/flow_dissector.c:1126 (P)
__skb_get_hash_net+0xe0/0x29c net/core/flow_dissector.c:1903
skb_get_hash include/linux/skbuff.h:1663 [inline]
seg6_make_flowlabel+0xcc/0x1ec net/ipv6/seg6_iptunnel.c:132
__seg6_do_srh_encap+0x320/0xbf4 net/ipv6/seg6_iptunnel.c:161
seg6_do_srh+0x4b4/0xa44 net/ipv6/seg6_iptunnel.c:431
seg6_output_core+0x164/0x688 net/ipv6/seg6_iptunnel.c:681
seg6_output+0x44/0x1ac net/ipv6/seg6_iptunnel.c:744
lwtunnel_output+0x3d0/0x664 net/core/lwtunnel.c:356
dst_output include/net/dst.h:470 [inline]
ip_local_out+0x110/0x148 net/ipv4/ip_output.c:131
iptunnel_xmit+0x50c/0xd38 net/ipv4/ip_tunnel_core.c:97
udp_tunnel_xmit_skb+0x220/0x348 net/ipv4/udp_tunnel_core.c:187
tipc_udp_xmit+0x75c/0x9c0 net/tipc/udp_media.c:202
tipc_udp_send_msg+0x214/0x374 net/tipc/udp_media.c:274
tipc_bearer_xmit_skb+0x260/0x3b0 net/tipc/bearer.c:576
tipc_enable_bearer net/tipc/bearer.c:366 [inline]
__tipc_nl_bearer_enable+0xc90/0xfb0 net/tipc/bearer.c:1048
tipc_nl_bearer_enable+0x2c/0x48 net/tipc/bearer.c:1057
genl_family_rcv_msg_doit+0x1e4/0x2d4 net/netlink/genetlink.c:1114 |
| In the Linux kernel, the following vulnerability has been resolved:
namespace: refuse an automount below a mount that is in no namespace
It's possible to add autmounts even when the parent mount isn't in the
mount namespace of the caller. The only requirement we have is that the
parent mount namespace must not be NULL, i.e., unmounted.
Problem is that clone_private_mount() has MNT_NS_INTERNAL which makes
that trivially true. So that passes the test and attach_recursive_mnt()
accepts that as a mount point and funny enough, count_mounts()
dereferences MNT_NS_INTERNAL. The problem is it is an error pointer...
So we can reach this in userspace via fanotify. A filesystem mark on the
lower filesystem of an overlay reports paths on the layer clone and
reading the event hands out a descriptor on it. For example with debugfs
as the lower layer it goes kaboom:
openat(evfd, "tracing", O_DIRECTORY)
Oops: general protection fault
KASAN: null-ptr-deref in range [0x1d0-0x1d7]
RIP: 0010:count_mounts+0x35/0x200
attach_recursive_mnt
finish_automount
And since that sleeping beauty happens under namespace_sem held for
writing every mount operation on the system blocks from then on.
Congrats.
Use is_mounted() instead which rejects unmounted and internal mounts
alike. The open fails with EINVAL just as it did before
clone_private_mount() used MNT_NS_INTERNAL. |
| In the Linux kernel, the following vulnerability has been resolved:
tcp: reject net_iov in zerocopy receive mapping hints
After copying a readable prefix, receive_fallback_to_copy() asks
tcp_zerocopy_set_hint_for_skb() where page mapping can resume. If the
next skb is unreadable, find_next_mappable_frag() passes its net_iov
fragment to can_map_frag().
skb_frag_page() returns NULL for a net_iov, but can_map_frag()
dereferences it in PageCompound(). A v7.2 KASAN run on a connected TCP
socket with 64 readable bytes followed by a 4096-byte NET_IOV_DMABUF
fragment reported:
BUG: KASAN: null-ptr-deref in can_map_frag
tcp_zerocopy_receive -> can_map_frag
Kernel panic - not syncing: KASAN: panic_on_warn set
The diagnostic inserted the net_iov directly because the test host has
no devmem-capable NIC. Hardware end-to-end reachability remains untested
and requires CONFIG_NET_DEVMEM plus a supported DMA-buf-bound RX queue.
Reject all net_iov fragments before skb_frag_page(). This covers both
DMABUF and IOURING net_iov types while leaving page-backed checks
unchanged. With the guard, the same queue copied the readable prefix,
returned a 4096-byte skip hint, and completed without a fault. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: RFCOMM: Fix NULL tty_dev dereference in rfcomm_dev_shutdown
syzbot hit a NULL pointer dereference in rfcomm_dev_shutdown() when an
RFCOMM tty is closed.
rfcomm_dev_add() puts the new device on rfcomm_dev_list first and only
then registers the tty device and saves it in dev->tty_dev. If that
registration fails, dev->tty_dev is never set at all. The device can be
looked up in the meantime, so an open() of /dev/rfcommN gets through
rfcomm_tty_install() and attaches to it. When that tty is closed again,
rfcomm_dev_shutdown() uses dev->tty_dev without checking it:
Oops: general protection fault, probably for non-canonical address
KASAN: null-ptr-deref in range [0x0000000000000040-0x0000000000000047]
RIP: 0010:rfcomm_dev_shutdown+0x48/0xb0 net/bluetooth/rfcomm/tty.c:131
Call Trace:
tty_port_shutdown+0x1bf/0x220 drivers/tty/tty_port.c:372
tty_port_close+0x4e/0x150 drivers/tty/tty_port.c:705
tty_release+0x359/0x1670 drivers/tty/tty_io.c:1718
__fput+0x418/0xa50 fs/file_table.c:512
rfcomm_dev_destruct() already copes with a NULL dev->tty_dev. Add the
same check to rfcomm_dev_shutdown(), so the tty device is only moved
when it was actually registered. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: hci_sock: Serialize dead-device detachment
Rebinding an HCI socket after its controller is unregistered can race
monitor control replay and crash the kernel. hci_sock_bind() clears
hci_pi(sk)->hdev and drops the device reference under only the socket
lock, whereas send_monitor_control_replay() holds hci_sk_list.lock for
reading.
Replay can observe a non-NULL hdev, then bind can clear it and drop the
last reference before create_monitor_ctrl_open() reads hdev->id. This
can cause a NULL pointer dereference if the pointer is reloaded, or a
use-after-free if the old pointer is retained.
The kernel reported:
KASAN: null-ptr-deref in range [0x0000000000000068-0x000000000000006f]
RIP: 0010:create_monitor_ctrl_open+0x579/0x800
Call Trace:
hci_sock_bind+0xd96/0x1190
__sys_bind+0x166/0x200
__x64_sys_bind+0x6d/0xb0
do_syscall_64+0xdd/0x4a0
entry_SYSCALL_64_after_hwframe+0x77/0x7f
The same missing serialization lets hci_send_to_sock() select a socket
for the old device and queue its frame after bind has detached the socket
or installed a new binding.
Take hci_sk_list.lock for writing when clearing the device pointer and
resetting the socket state. This waits for existing replay and delivery
readers to finish before detachment and prevents later readers from
using the old binding. Keep hci_dev_put() outside the critical section
because the final device release can sleep. |
| In the Linux kernel, the following vulnerability has been resolved:
net: emac: move setting of netops to fix crash
fixes the following crash on driver initialization:
|BUG: Kernel NULL pointer dereference on read at 0x00000158
|Faulting instruction address: 0xc0566b40
|Oops: Kernel access of bad area, sig: 11 [#1]
|BE PAGE_SIZE=4K PowerPC 44x Platform
|Modules linked in:
|CPU: 0 UID: 0 PID: 1 Comm: swapper/0 Tainted: GW 7.3.0-rc3+ #1
|Tainted: [W]=WARN
|Hardware name: MyBook Live APM821XX 0x12c41c83 PowerPC 44x Platform
|NIP: c0566b40 LR: c05648f8 CTR: c04c1e9c
|REGS: c1053a20 TRAP: 0300 Tainted: GW (7.3.0-rc3+)
|MSR: 0002b000 <CE,EE,FP,ME> CR: 24008808 XER: 00000000
|DEAR: 00000158 ESR: 00000000
|GPR00: c05648f8 c1053b10 c1063600 c1030000 c5ab3000 00000000 [...]
|GPR08: 00000002 00000000 00000000 c1053b40 84002808 00000000 [...]
|GPR16: cfffd210 00000002 c0beafcc cfffc960 00000000 c1030644 [...]
|GPR24: c0beafbc c1037000 00000000 0000000a 00000000 c1030000 [...]
|NIP [c0566b40] phy_link_topo_add_phy+0x2c/0x1d0
|LR [c05648f8] phy_attach_direct+0x1a4/0x368
|Call Trace:
|[c1053b10] [c0811e04] klist_put+0x54/0xb4 (unreliable)
|[c1053b40] [c05648f8] phy_attach_direct+0x1a4/0x368
|[c1053b70] [c0564ae8] phy_connect_direct+0x2c/0x60
|[c1053b90] [c056c7a8] of_phy_connect+0x50/0x74
|[c1053bc0] [c0572a88] emac_probe+0xd50/0x119c
|[c1053c90] [c04cb770] platform_probe+0x74/0xa4
|[c1053cb0] [c04c8f08] really_probe+0x120/0x2b0
|[c1053cd0] [c04c9254] __driver_probe_device+0x1bc/0x1fc
|[c1053d00] [c04c9334] driver_probe_device+0x38/0xa8
|[c1053d30] [c04c9560] __driver_attach+0xf4/0x10c
|[c1053d50] [c04c6af8] bus_for_each_dev+0x68/0xd0
|[c1053d90] [c04c7c34] bus_add_driver+0xcc/0x1ec
|[c1053dc0] [c04c9f6c] driver_register+0xcc/0x110
|[c1053de0] [c0aa3f40] emac_init+0x1c4/0x200
This bug showed up starting with v7.3-rc1. At the NIP in
phy_link_topo_add_phy() is a netdev_need_ops_lock() check.
This was added by the following
commit ded86da4bbb7 ("net: ethtool: relax ethnl_req_get_phydev() locking assertion")
The bug shows up because at the time of_phy_connect() was called, the
netdev_ops were *not yet* determined. My fix is to move the code that
sets netdev_ops+commac.ops+ethtool_ops further up as emac_init_config()
derives that by looking at the device-tree and sets the required
dev->phy_mode accordingly.
During review, the Sashiko bot's AI stated that the commac assignment
became a dead store. Great catch! To keep the original behavior as-is,
one mentioned option "set dev->commac.ops = &emac_commac_ops only in
the non-gige case?" sounded like a great plan. So the dev->commac.ops
assignment for the non-gige-case moves into the else block.
This patch was tested on a WD MyBook Live (RGMII). the device now works again. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: spinand: fix NULL pointer dereference with no ECC engine
When "nand-no-ecc-engine" is set in DT, nanddev_get_ecc_engine() takes
the NAND_ECC_ENGINE_TYPE_NONE path and returns success while leaving
nand->ecc.engine NULL. The SPI-NAND code nevertheless dereferences it
unconditionally to test for a pipelined engine, so probing such a
device oopses immediately.
Rather than open-coding the test three times, add a
nand_ecc_is_pipelined() helper to the NAND core that folds the NULL
check into the integration comparison, and use it everywhere. Future
callers then cannot reintroduce the problem. |
| pupnp is an SDK for development of UPnP device and control point applications. Prior to 2.0.2, ixmlNode_compare in ixml/src/node.c passes the nullable nodeValue, namespaceURI, prefix, and localName fields directly to strcmp. Non-namespaced attributes created by ixmlDocument_createAttribute legitimately leave those fields NULL. When ixmlElement_removeAttributeNode compares two distinct attribute objects with the same nodeName through find_condition_node, the pointer-identity shortcut does not apply and the comparison dereferences NULL, causing a process crash when application handling of attacker-controlled XML reaches this path. This issue is fixed in 2.0.2. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Remove sink usage from DPMS
[Why]
stream->sink is optional and can be null, so should always be checked
before dereference. Additionally, most of its usage in DPMS sequences
is for stream->sink->link, which can be replaced with stream->link,
as the two should always be the same.
[How]
* Replace stream->sink->link in DPMS on/off
* Add assert to USB4 BW allocation where sink is required
* Avoid inconsistencies in resource access, e.g. don't repeat
stream->link after it was already saved to a local variable
* Pull out effective VPG calculation to helper getter
* Formatting fixes |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: arm64: Derive GUEST_HAS_SVE from the SVE feature bit at EL2
pkvm_init_features_from_host() takes KVM_ARCH_FLAG_GUEST_HAS_SVE and
KVM_ARM_VCPU_SVE from the host separately, but pkvm_vcpu_init_sve()
tests the bit while vcpu_has_sve() reads the flag. A host that sets the
flag without the bit gets a vCPU with a NULL sve_state that the world
switch loads the guest's SVE state from.
Derive the flag from the bit, and drop the protected path's copy of the
host's flag, which is dead code since protected VMs are not allowed SVE. |
| A Null pointer dereference problem was found in ida_free in lib/idr.c in the Linux Kernel. This issue may allow an attacker using this library to cause a denial of service problem due to a missing check at a function return. |
| kin-openapi is a Go project for handling OpenAPI files. Prior to 0.145.0, openapi3.Loader can dereference a nil SchemaRef.Value while resolving a self-referential additionalProperties JSON Reference such as a schema that points to its own additionalProperties member. Loading an attacker-controlled OpenAPI document through LoadFromData, LoadFromFile, or LoadFromURI reaches resolveComponent before document validation and can panic the loading process. Resolved additionalProperties schemas and ordinary recursive schemas do not take the vulnerable nil-value path. This issue is fixed in version 0.145.0. |
| kin-openapi is a Go project for handling OpenAPI files. Prior to 0.146.0, openapi3filter.ValidateResponse passes a nil response header schema to decodeValue when an OpenAPI document declares the header with content instead of schema. The document passes validation, but every response validation for the affected operation dereferences the nil schema and panics even when the response does not contain the declared header. Applications that ingest an untrusted specification can expose this as remote availability impact, while applications using only trusted local specifications still crash when the affected operation is exercised. This issue is fixed in version 0.146.0. |
| kin-openapi is a Go project for handling OpenAPI files. Prior to 0.148.0, the OpenAPI 3.1 validation path passes YAML NaN and infinity numeric values to santhosh-tekuri/jsonschema v6.0.2 without applying kin-openapi's existing finite-number guards. A remote unauthenticated client can send an application/yaml or application/x-yaml request body containing .nan, .inf, or -.inf to an operation with a numeric constraint, causing the dependency to create and dereference a nil big.Rat during ValidateRequest. Standard net/http servers recover the panic per connection, while other hosts or application goroutines may terminate the process. This issue is fixed in version 0.148.0. |
| kin-openapi is a Go project for handling OpenAPI files. From 0.136.0 until 0.149.0, three openapi3filter decoder paths that were missed by the fix for GHSA-p6wj-qrr4-pgh5 lack a nil-items guard for legal OpenAPI 3.1 array schemas. An unauthenticated remote client can trigger a deterministic nil-pointer panic through an array query parameter, a deepObject query parameter containing an array property, or an application/x-www-form-urlencoded request body whose array property appears inside an allOf, anyOf, or oneOf subschema. The query and composed-body paths reach urlValuesDecoder.parseArray, while the deepObject path reaches buildResObj, and all pass a nil items schema into code that dereferences it. This issue is fixed in version 0.149.0. |
| The ONVIF service on the E3 can be rendered unresponsive by sending malformed or incomplete requests to certain operations. The affected service stops accepting new connections while the rest of the device continues operating normally, and will recover automatically after a period. This can be triggered repeatedly by any unauthenticated party with network access to the device. |
| libIEC61850 is an open-source implementation of IEC 61850 client and server protocols including MMS, GOOSE, Sampled Values, and R-Session. Prior to 1.6.2, alternateArrayAccess in src/mms/iso_mms/server/mms_read_service.c does not validate an alternate-access sub-array range when numberOfElements is greater than zero. An out-of-range MmsValue_getElement call returns NULL, and the sub-array branch passes that value to MmsValue_isDeletable, causing a NULL pointer dereference. A remote MMS Read request can therefore crash servers whose data models contain arrays, while the single-element error path handles the same invalid index safely. This issue is fixed in version 1.6.2. |
