| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/vt-d: Clear Present bit before tearing down PASID entry
The Intel VT-d Scalable Mode PASID table entry consists of 512 bits (64
bytes). When tearing down an entry, the current implementation zeros the
entire 64-byte structure immediately using multiple 64-bit writes.
Since the IOMMU hardware may fetch these 64 bytes using multiple
internal transactions (e.g., four 128-bit bursts), updating or zeroing
the entire entry while it is active (P=1) risks a "torn" read. If a
hardware fetch occurs simultaneously with the CPU zeroing the entry, the
hardware could observe an inconsistent state, leading to unpredictable
behavior or spurious faults.
Follow the "Guidance to Software for Invalidations" in the VT-d spec
(Section 6.5.3.3) by implementing the recommended ownership handshake:
1. Clear only the 'Present' (P) bit of the PASID entry.
2. Use a dma_wmb() to ensure the cleared bit is visible to hardware
before proceeding.
3. Execute the required invalidation sequence (PASID cache, IOTLB, and
Device-TLB flush) to ensure the hardware has released all cached
references.
4. Only after the flushes are complete, zero out the remaining fields
of the PASID entry.
Also, add a dma_wmb() in pasid_set_present() to ensure that all other
fields of the PASID entry are visible to the hardware before the Present
bit is set. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nfnetlink_queue: do shared-unconfirmed check before segmentation
Ulrich reports a regression with nfqueue:
If an application did not set the 'F_GSO' capability flag and a gso
packet with an unconfirmed nf_conn entry is received all packets are
now dropped instead of queued, because the check happens after
skb_gso_segment(). In that case, we did have exclusive ownership
of the skb and its associated conntrack entry. The elevated use
count is due to skb_clone happening via skb_gso_segment().
Move the check so that its peformed vs. the aggregated packet.
Then, annotate the individual segments except the first one so we
can do a 2nd check at reinject time.
For the normal case, where userspace does in-order reinjects, this avoids
packet drops: first reinjected segment continues traversal and confirms
entry, remaining segments observe the confirmed entry.
While at it, simplify nf_ct_drop_unconfirmed(): We only care about
unconfirmed entries with a refcnt > 1, there is no need to special-case
dying entries.
This only happens with UDP. With TCP, the only unconfirmed packet will
be the TCP SYN, those aren't aggregated by GRO.
Next patch adds a udpgro test case to cover this scenario. |
| In the Linux kernel, the following vulnerability has been resolved:
nouveau/gsp: drop WARN_ON in ACPI probes
These WARN_ONs seem to trigger a lot, and we don't seem to have a
plan to fix them, so just drop them, as they are most likely
harmless. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: RX, Fix XDP multi-buf frag counting for legacy RQ
XDP multi-buf programs can modify the layout of the XDP buffer when the
program calls bpf_xdp_pull_data() or bpf_xdp_adjust_tail(). The
referenced commit in the fixes tag corrected the assumption in the mlx5
driver that the XDP buffer layout doesn't change during a program
execution. However, this fix introduced another issue: the dropped
fragments still need to be counted on the driver side to avoid page
fragment reference counting issues.
Such issue can be observed with the
test_xdp_native_adjst_tail_shrnk_data selftest when using a payload of
3600 and shrinking by 256 bytes (an upcoming selftest patch): the last
fragment gets released by the XDP code but doesn't get tracked by the
driver. This results in a negative pp_ref_count during page release and
the following splat:
WARNING: include/net/page_pool/helpers.h:297 at mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core], CPU#12: ip/3137
Modules linked in: [...]
CPU: 12 UID: 0 PID: 3137 Comm: ip Not tainted 6.19.0-rc3+ #12 NONE
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.3-0-ga6ed6b701f0a-prebuilt.qemu.org 04/01/2014
RIP: 0010:mlx5e_page_release_fragmented.isra.0+0x4a/0x50 [mlx5_core]
[...]
Call Trace:
<TASK>
mlx5e_dealloc_rx_wqe+0xcb/0x1a0 [mlx5_core]
mlx5e_free_rx_descs+0x7f/0x110 [mlx5_core]
mlx5e_close_rq+0x50/0x60 [mlx5_core]
mlx5e_close_queues+0x36/0x2c0 [mlx5_core]
mlx5e_close_channel+0x1c/0x50 [mlx5_core]
mlx5e_close_channels+0x45/0x80 [mlx5_core]
mlx5e_safe_switch_params+0x1a5/0x230 [mlx5_core]
mlx5e_change_mtu+0xf3/0x2f0 [mlx5_core]
netif_set_mtu_ext+0xf1/0x230
do_setlink.isra.0+0x219/0x1180
rtnl_newlink+0x79f/0xb60
rtnetlink_rcv_msg+0x213/0x3a0
netlink_rcv_skb+0x48/0xf0
netlink_unicast+0x24a/0x350
netlink_sendmsg+0x1ee/0x410
__sock_sendmsg+0x38/0x60
____sys_sendmsg+0x232/0x280
___sys_sendmsg+0x78/0xb0
__sys_sendmsg+0x5f/0xb0
[...]
do_syscall_64+0x57/0xc50
This patch fixes the issue by doing page frag counting on all the
original XDP buffer fragments for all relevant XDP actions (XDP_TX ,
XDP_REDIRECT and XDP_PASS). This is basically reverting to the original
counting before the commit in the fixes tag.
As frag_page is still pointing to the original tail, the nr_frags
parameter to xdp_update_skb_frags_info() needs to be calculated
in a different way to reflect the new nr_frags. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: mipi-i3c-hci: Correct RING_CTRL_ABORT handling in DMA dequeue
The logic used to abort the DMA ring contains several flaws:
1. The driver unconditionally issues a ring abort even when the ring has
already stopped.
2. The completion used to wait for abort completion is never
re-initialized, resulting in incorrect wait behavior.
3. The abort sequence unintentionally clears RING_CTRL_ENABLE, which
resets hardware ring pointers and disrupts the controller state.
4. If the ring is already stopped, the abort operation should be
considered successful without attempting further action.
Fix the abort handling by checking whether the ring is running before
issuing an abort, re-initializing the completion when needed, ensuring that
RING_CTRL_ENABLE remains asserted during abort, and treating an already
stopped ring as a successful condition. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: reserve enough transaction items for qgroup ioctls
Currently our qgroup ioctls don't reserve any space, they just do a
transaction join, which does not reserve any space, neither for the quota
tree updates nor for the delayed refs generated when updating the quota
tree. The quota root uses the global block reserve, which is fine most of
the time since we don't expect a lot of updates to the quota root, or to
be too close to -ENOSPC such that other critical metadata updates need to
resort to the global reserve.
However this is not optimal, as not reserving proper space may result in a
transaction abort due to not reserving space for delayed refs and then
abusing the use of the global block reserve.
For example, the following reproducer (which is unlikely to model any
real world use case, but just to illustrate the problem), triggers such a
transaction abort due to -ENOSPC when running delayed refs:
$ cat test.sh
#!/bin/bash
DEV=/dev/nullb0
MNT=/mnt/nullb0
umount $DEV &> /dev/null
# Limit device to 1G so that it's much faster to reproduce the issue.
mkfs.btrfs -f -b 1G $DEV
mount -o commit=600 $DEV $MNT
fallocate -l 800M $MNT/filler
btrfs quota enable $MNT
for ((i = 1; i <= 400000; i++)); do
btrfs qgroup create 1/$i $MNT
done
umount $MNT
When running this, we can see in dmesg/syslog that a transaction abort
happened:
[436.490] BTRFS error (device nullb0): failed to run delayed ref for logical 30408704 num_bytes 16384 type 176 action 1 ref_mod 1: -28
[436.493] ------------[ cut here ]------------
[436.494] BTRFS: Transaction aborted (error -28)
[436.495] WARNING: fs/btrfs/extent-tree.c:2247 at btrfs_run_delayed_refs+0xd9/0x110 [btrfs], CPU#4: umount/2495372
[436.497] Modules linked in: btrfs loop (...)
[436.508] CPU: 4 UID: 0 PID: 2495372 Comm: umount Tainted: G W 6.19.0-rc8-btrfs-next-225+ #1 PREEMPT(full)
[436.510] Tainted: [W]=WARN
[436.511] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
[436.513] RIP: 0010:btrfs_run_delayed_refs+0xdf/0x110 [btrfs]
[436.514] Code: 0f 82 ea (...)
[436.518] RSP: 0018:ffffd511850b7d78 EFLAGS: 00010292
[436.519] RAX: 00000000ffffffe4 RBX: ffff8f120dad37e0 RCX: 0000000002040001
[436.520] RDX: 0000000000000002 RSI: 00000000ffffffe4 RDI: ffffffffc090fd80
[436.522] RBP: 0000000000000000 R08: 0000000000000001 R09: ffffffffc04d1867
[436.523] R10: ffff8f18dc1fffa8 R11: 0000000000000003 R12: ffff8f173aa89400
[436.524] R13: 0000000000000000 R14: ffff8f173aa89400 R15: 0000000000000000
[436.526] FS: 00007fe59045d840(0000) GS:ffff8f192e22e000(0000) knlGS:0000000000000000
[436.527] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[436.528] CR2: 00007fe5905ff2b0 CR3: 000000060710a002 CR4: 0000000000370ef0
[436.530] Call Trace:
[436.530] <TASK>
[436.530] btrfs_commit_transaction+0x73/0xc00 [btrfs]
[436.531] ? btrfs_attach_transaction_barrier+0x1e/0x70 [btrfs]
[436.532] sync_filesystem+0x7a/0x90
[436.533] generic_shutdown_super+0x28/0x180
[436.533] kill_anon_super+0x12/0x40
[436.534] btrfs_kill_super+0x12/0x20 [btrfs]
[436.534] deactivate_locked_super+0x2f/0xb0
[436.534] cleanup_mnt+0xea/0x180
[436.535] task_work_run+0x58/0xa0
[436.535] exit_to_user_mode_loop+0xed/0x480
[436.536] ? __x64_sys_umount+0x68/0x80
[436.536] do_syscall_64+0x2a5/0xf20
[436.537] entry_SYSCALL_64_after_hwframe+0x76/0x7e
[436.537] RIP: 0033:0x7fe5906b6217
[436.538] Code: 0d 00 f7 (...)
[436.540] RSP: 002b:00007ffcd87a61f8 EFLAGS: 00000246 ORIG_RAX: 00000000000000a6
[436.541] RAX: 0000000000000000 RBX: 00005618b9ecadc8 RCX: 00007fe5906b6217
[436.541] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 00005618b9ecb100
[436.542] RBP: 0000000000000000 R08: 00007ffcd87a4fe0 R09: 00000000ffffffff
[436.544] R10: 0000000000000103 R11:
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: don't send a 6E related command when not supported
MCC_ALLOWED_AP_TYPE_CMD is related to 6E support. Do not send it if the
device doesn't support 6E.
Apparently, the firmware is mistakenly advertising support for this
command even on AX201 which does not support 6E and then the firmware
crashes. |
| In the Linux kernel, the following vulnerability has been resolved:
soc/tegra: pmc: Fix unsafe generic_handle_irq() call
Currently, when resuming from system suspend on Tegra platforms,
the following warning is observed:
WARNING: CPU: 0 PID: 14459 at kernel/irq/irqdesc.c:666
Call trace:
handle_irq_desc+0x20/0x58 (P)
tegra186_pmc_wake_syscore_resume+0xe4/0x15c
syscore_resume+0x3c/0xb8
suspend_devices_and_enter+0x510/0x540
pm_suspend+0x16c/0x1d8
The warning occurs because generic_handle_irq() is being called from
a non-interrupt context which is considered as unsafe.
Fix this warning by deferring generic_handle_irq() call to an IRQ work
which gets executed in hard IRQ context where generic_handle_irq()
can be called safely.
When PREEMPT_RT kernels are used, regular IRQ work (initialized with
init_irq_work) is deferred to run in per-CPU kthreads in preemptible
context rather than hard IRQ context. Hence, use the IRQ_WORK_INIT_HARD
variant so that with PREEMPT_RT kernels, the IRQ work is processed in
hardirq context instead of being deferred to a thread which is required
for calling generic_handle_irq().
On non-PREEMPT_RT kernels, both init_irq_work() and IRQ_WORK_INIT_HARD()
execute in IRQ context, so this change has no functional impact for
standard kernel configurations.
[treding@nvidia.com: miscellaneous cleanups] |
| In the Linux kernel, the following vulnerability has been resolved:
media: verisilicon: Avoid G2 bus error while decoding H.264 and HEVC
For the i.MX8MQ platform, there is a hardware limitation: the g1 VPU and
g2 VPU cannot decode simultaneously; otherwise, it will cause below bus
error and produce corrupted pictures, even potentially lead to system hang.
[ 110.527986] hantro-vpu 38310000.video-codec: frame decode timed out.
[ 110.583517] hantro-vpu 38310000.video-codec: bus error detected.
Therefore, it is necessary to ensure that g1 and g2 operate alternately.
This allows for successful multi-instance decoding of H.264 and HEVC.
To achieve this, g1 and g2 share the same v4l2_m2m_dev, and then the
v4l2_m2m_dev can handle the scheduling. |
| In the Linux kernel, the following vulnerability has been resolved:
md raid: fix hang when stopping arrays with metadata through dm-raid
When using device-mapper's dm-raid target, stopping a RAID array can cause
the system to hang under specific conditions.
This occurs when:
- A dm-raid managed device tree is suspended from top to bottom
(the top-level RAID device is suspended first, followed by its
underlying metadata and data devices)
- The top-level RAID device is then removed
Removing the top-level device triggers a hang in the following sequence:
the dm-raid destructor calls md_stop(), which tries to flush the
write-intent bitmap by writing to the metadata sub-devices. However, these
devices are already suspended, making them unable to complete the write-intent
operations and causing an indefinite block.
Fix:
- Prevent bitmap flushing when md_stop() is called from dm-raid
destructor context
and avoid a quiescing/unquescing cycle which could also cause I/O
- Still allow write-intent bitmap flushing when called from dm-raid
suspend context
This ensures that RAID array teardown can complete successfully even when the
underlying devices are in a suspended state.
This second patch uses md_is_rdwr() to distinguish between suspend and
destructor paths as elaborated on above. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: don't BUG() on unexpected delayed ref type in run_one_delayed_ref()
There is no need to BUG(), we can just return an error and log an error
message. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: do not ASSERT() when the fs flips RO inside btrfs_repair_io_failure()
[BUG]
There is a bug report that when btrfs hits ENOSPC error in a critical
path, btrfs flips RO (this part is expected, although the ENOSPC bug
still needs to be addressed).
The problem is after the RO flip, if there is a read repair pending, we
can hit the ASSERT() inside btrfs_repair_io_failure() like the following:
BTRFS info (device vdc): relocating block group 30408704 flags metadata|raid1
------------[ cut here ]------------
BTRFS: Transaction aborted (error -28)
WARNING: fs/btrfs/extent-tree.c:3235 at __btrfs_free_extent.isra.0+0x453/0xfd0, CPU#1: btrfs/383844
Modules linked in: kvm_intel kvm irqbypass
[...]
---[ end trace 0000000000000000 ]---
BTRFS info (device vdc state EA): 2 enospc errors during balance
BTRFS info (device vdc state EA): balance: ended with status: -30
BTRFS error (device vdc state EA): parent transid verify failed on logical 30556160 mirror 2 wanted 8 found 6
BTRFS error (device vdc state EA): bdev /dev/nvme0n1 errs: wr 0, rd 0, flush 0, corrupt 10, gen 0
[...]
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
------------[ cut here ]------------
assertion failed: !(fs_info->sb->s_flags & SB_RDONLY) :: 0, in fs/btrfs/bio.c:938
kernel BUG at fs/btrfs/bio.c:938!
Oops: invalid opcode: 0000 [#1] SMP NOPTI
CPU: 0 UID: 0 PID: 868 Comm: kworker/u8:13 Tainted: G W N 6.19.0-rc6+ #4788 PREEMPT(full)
Tainted: [W]=WARN, [N]=TEST
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
Workqueue: btrfs-endio simple_end_io_work
RIP: 0010:btrfs_repair_io_failure.cold+0xb2/0x120
RSP: 0000:ffffc90001d2bcf0 EFLAGS: 00010246
RAX: 0000000000000051 RBX: 0000000000001000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8305cf42 RDI: 00000000ffffffff
RBP: 0000000000000002 R08: 00000000fffeffff R09: ffffffff837fa988
R10: ffffffff8327a9e0 R11: 6f69747265737361 R12: ffff88813018d310
R13: ffff888168b8a000 R14: ffffc90001d2bd90 R15: ffff88810a169000
FS: 0000000000000000(0000) GS:ffff8885e752c000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
------------[ cut here ]------------
[CAUSE]
The cause of -ENOSPC error during the test case btrfs/124 is still
unknown, although it's known that we still have cases where metadata can
be over-committed but can not be fulfilled correctly, thus if we hit
such ENOSPC error inside a critical path, we have no choice but abort
the current transaction.
This will mark the fs read-only.
The problem is inside the btrfs_repair_io_failure() path that we require
the fs not to be mount read-only. This is normally fine, but if we are
doing a read-repair meanwhile the fs flips RO due to a critical error,
we can enter btrfs_repair_io_failure() with super block set to
read-only, thus triggering the above crash.
[FIX]
Just replace the ASSERT() with a proper return if the fs is already
read-only. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Skip vcn poison irq release on VF
VF doesn't enable VCN poison irq in VCNv2.5. Skip releasing it and avoid
call trace during deinitialization.
[ 71.913601] [drm] clean up the vf2pf work item
[ 71.915088] ------------[ cut here ]------------
[ 71.915092] WARNING: CPU: 3 PID: 1079 at /tmp/amd.aFkFvSQl/amd/amdgpu/amdgpu_irq.c:641 amdgpu_irq_put+0xc6/0xe0 [amdgpu]
[ 71.915355] Modules linked in: amdgpu(OE-) amddrm_ttm_helper(OE) amdttm(OE) amddrm_buddy(OE) amdxcp(OE) amddrm_exec(OE) amd_sched(OE) amdkcl(OE) drm_suballoc_helper drm_display_helper cec rc_core i2c_algo_bit video wmi binfmt_misc nls_iso8859_1 intel_rapl_msr intel_rapl_common input_leds joydev serio_raw mac_hid qemu_fw_cfg sch_fq_codel dm_multipath scsi_dh_rdac scsi_dh_emc scsi_dh_alua efi_pstore ip_tables x_tables autofs4 btrfs blake2b_generic raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 hid_generic crct10dif_pclmul crc32_pclmul polyval_clmulni polyval_generic ghash_clmulni_intel usbhid 8139too sha256_ssse3 sha1_ssse3 hid psmouse bochs i2c_i801 ahci drm_vram_helper libahci i2c_smbus lpc_ich drm_ttm_helper 8139cp mii ttm aesni_intel crypto_simd cryptd
[ 71.915484] CPU: 3 PID: 1079 Comm: rmmod Tainted: G OE 6.8.0-87-generic #88~22.04.1-Ubuntu
[ 71.915489] Hardware name: Red Hat KVM/RHEL, BIOS 1.16.3-2.el9_5.1 04/01/2014
[ 71.915492] RIP: 0010:amdgpu_irq_put+0xc6/0xe0 [amdgpu]
[ 71.915768] Code: 75 84 b8 ea ff ff ff eb d4 44 89 ea 48 89 de 4c 89 e7 e8 fd fc ff ff 5b 41 5c 41 5d 41 5e 5d 31 d2 31 f6 31 ff e9 55 30 3b c7 <0f> 0b eb d4 b8 fe ff ff ff eb a8 e9 b7 3b 8a 00 66 2e 0f 1f 84 00
[ 71.915771] RSP: 0018:ffffcf0800eafa30 EFLAGS: 00010246
[ 71.915775] RAX: 0000000000000000 RBX: ffff891bda4b0668 RCX: 0000000000000000
[ 71.915777] RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
[ 71.915779] RBP: ffffcf0800eafa50 R08: 0000000000000000 R09: 0000000000000000
[ 71.915781] R10: 0000000000000000 R11: 0000000000000000 R12: ffff891bda480000
[ 71.915782] R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000000
[ 71.915792] FS: 000070cff87c4c40(0000) GS:ffff893abfb80000(0000) knlGS:0000000000000000
[ 71.915795] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 71.915797] CR2: 00005fa13073e478 CR3: 000000010d634006 CR4: 0000000000770ef0
[ 71.915800] PKRU: 55555554
[ 71.915802] Call Trace:
[ 71.915805] <TASK>
[ 71.915809] vcn_v2_5_hw_fini+0x19e/0x1e0 [amdgpu] |
| In the Linux kernel, the following vulnerability has been resolved:
drm: renesas: rz-du: mipi_dsi: fix kernel panic when rebooting for some panels
Since commit 56de5e305d4b ("clk: renesas: r9a07g044: Add MSTOP for RZ/G2L")
we may get the following kernel panic, for some panels, when rebooting:
systemd-shutdown[1]: Rebooting.
Call trace:
...
do_serror+0x28/0x68
el1h_64_error_handler+0x34/0x50
el1h_64_error+0x6c/0x70
rzg2l_mipi_dsi_host_transfer+0x114/0x458 (P)
mipi_dsi_device_transfer+0x44/0x58
mipi_dsi_dcs_set_display_off_multi+0x9c/0xc4
ili9881c_unprepare+0x38/0x88
drm_panel_unprepare+0xbc/0x108
This happens for panels that need to send MIPI-DSI commands in their
unprepare() callback. Since the MIPI-DSI interface is stopped at that
point, rzg2l_mipi_dsi_host_transfer() triggers the kernel panic.
Fix by moving rzg2l_mipi_dsi_stop() to new callback function
rzg2l_mipi_dsi_atomic_post_disable().
With this change we now have the correct power-down/stop sequence:
systemd-shutdown[1]: Rebooting.
rzg2l-mipi-dsi 10850000.dsi: rzg2l_mipi_dsi_atomic_disable(): entry
ili9881c-dsi 10850000.dsi.0: ili9881c_unprepare(): entry
rzg2l-mipi-dsi 10850000.dsi: rzg2l_mipi_dsi_atomic_post_disable(): entry
reboot: Restarting system |
| In the Linux kernel, the following vulnerability has been resolved:
team: avoid NETDEV_CHANGEMTU event when unregistering slave
syzbot is reporting
unregister_netdevice: waiting for netdevsim0 to become free. Usage count = 3
ref_tracker: netdev@ffff88807dcf8618 has 1/2 users at
__netdev_tracker_alloc include/linux/netdevice.h:4400 [inline]
netdev_hold include/linux/netdevice.h:4429 [inline]
inetdev_init+0x201/0x4e0 net/ipv4/devinet.c:286
inetdev_event+0x251/0x1610 net/ipv4/devinet.c:1600
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_mtu net/core/dev.c:2318 [inline]
netif_set_mtu_ext+0x5aa/0x800 net/core/dev.c:9886
netif_set_mtu+0xd7/0x1b0 net/core/dev.c:9907
dev_set_mtu+0x126/0x260 net/core/dev_api.c:248
team_port_del+0xb07/0xcb0 drivers/net/team/team_core.c:1333
team_del_slave drivers/net/team/team_core.c:1936 [inline]
team_device_event+0x207/0x5b0 drivers/net/team/team_core.c:2929
notifier_call_chain+0x19d/0x3a0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2281 [inline]
call_netdevice_notifiers net/core/dev.c:2295 [inline]
__dev_change_net_namespace+0xcb7/0x2050 net/core/dev.c:12592
do_setlink+0x2ce/0x4590 net/core/rtnetlink.c:3060
rtnl_changelink net/core/rtnetlink.c:3776 [inline]
__rtnl_newlink net/core/rtnetlink.c:3935 [inline]
rtnl_newlink+0x15a9/0x1be0 net/core/rtnetlink.c:4072
rtnetlink_rcv_msg+0x7d5/0xbe0 net/core/rtnetlink.c:6958
netlink_rcv_skb+0x232/0x4b0 net/netlink/af_netlink.c:2550
netlink_unicast_kernel net/netlink/af_netlink.c:1318 [inline]
netlink_unicast+0x80f/0x9b0 net/netlink/af_netlink.c:1344
netlink_sendmsg+0x813/0xb40 net/netlink/af_netlink.c:1894
problem. Ido Schimmel found steps to reproduce
ip link add name team1 type team
ip link add name dummy1 mtu 1499 master team1 type dummy
ip netns add ns1
ip link set dev dummy1 netns ns1
ip -n ns1 link del dev dummy1
and also found that the same issue was fixed in the bond driver in
commit f51048c3e07b ("bonding: avoid NETDEV_CHANGEMTU event when
unregistering slave").
Let's do similar thing for the team driver, with commit ad7c7b2172c3 ("net:
hold netdev instance lock during sysfs operations") and commit 303a8487a657
("net: s/__dev_set_mtu/__netif_set_mtu/") also applied. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: qcom: q6asm: drop DSP responses for closed data streams
'Commit a354f030dbce ("ASoC: qcom: q6asm: handle the responses
after closing")' attempted to ignore DSP responses arriving
after a stream had been closed.
However, those responses were still handled, causing lockups.
Fix this by unconditionally dropping all DSP responses associated with
closed data streams. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5e: Fix "scheduling while atomic" in IPsec MAC address query
Fix a "scheduling while atomic" bug in mlx5e_ipsec_init_macs() by
replacing mlx5_query_mac_address() with ether_addr_copy() to get the
local MAC address directly from netdev->dev_addr.
The issue occurs because mlx5_query_mac_address() queries the hardware
which involves mlx5_cmd_exec() that can sleep, but it is called from
the mlx5e_ipsec_handle_event workqueue which runs in atomic context.
The MAC address is already available in netdev->dev_addr, so no need
to query hardware. This avoids the sleeping call and resolves the bug.
Call trace:
BUG: scheduling while atomic: kworker/u112:2/69344/0x00000200
__schedule+0x7ab/0xa20
schedule+0x1c/0xb0
schedule_timeout+0x6e/0xf0
__wait_for_common+0x91/0x1b0
cmd_exec+0xa85/0xff0 [mlx5_core]
mlx5_cmd_exec+0x1f/0x50 [mlx5_core]
mlx5_query_nic_vport_mac_address+0x7b/0xd0 [mlx5_core]
mlx5_query_mac_address+0x19/0x30 [mlx5_core]
mlx5e_ipsec_init_macs+0xc1/0x720 [mlx5_core]
mlx5e_ipsec_build_accel_xfrm_attrs+0x422/0x670 [mlx5_core]
mlx5e_ipsec_handle_event+0x2b9/0x460 [mlx5_core]
process_one_work+0x178/0x2e0
worker_thread+0x2ea/0x430 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Adjust PHY FSM transition to TX_EN-to-PLL_ON for TMDS on DCN35
[Why]
A backport of the change made for DCN401 that addresses an issue where
we turn off the PHY PLL when disabling TMDS output, which causes the
OTG to remain stuck.
The OTG being stuck can lead to a hang in the DCHVM's ability to ACK
invalidations when it thinks the HUBP is still on but it's not receiving
global sync.
The transition to PLL_ON needs to be atomic as there's no guarantee
that the thread isn't pre-empted or is able to complete before the
IOMMU watchdog times out.
[How]
Backport the implementation from dcn401 back to dcn35.
There's a functional difference in when the eDP output is disabled in
dcn401 code so we don't want to utilize it directly. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: fix 22000 series SMEM parsing
If the firmware were to report three LMACs (which doesn't
exist in hardware) then using "fwrt->smem_cfg.lmac[2]" is
an overrun of the array. Reject such and use IWL_FW_CHECK
instead of WARN_ON in this function. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: mixer: oss: Add card disconnect checkpoints
ALSA OSS mixer layer calls the kcontrol ops rather individually, and
pending calls might be not always caught at disconnecting the device.
For avoiding the potential UAF scenarios, add sanity checks of the
card disconnection at each entry point of OSS mixer accesses. The
rwsem is taken just before that check, hence the rest context should
be covered by that properly. |
